|
|
PDF LED22V1A Data sheet ( Hoja de datos )
| Número de pieza | LED22V1A | |
| Descripción | HIGH EFFICIENCY LED CONTROLLER | |
| Fabricantes | Analog Technologies | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LED22V1A (archivo pdf) en la parte inferior de esta página. Total 3 Páginas | ||
|
No Preview Available !
Analog Technologies, Inc.
LED22V1A
HIGH EFFICIENCY LED CONTROLLER
Main Features: output current adjustable, supply current monitoring, high efficiency, high power density, high
precision, small size, fault protection, low output ripple current and low cost.
Specifications
Part number:
Input voltage:
Output voltage:
Maximum output current:
Efficiency:
Dimming control voltage:
Packaging:
Operating temperature:
Dimension:
LED22V1A
7V to 22V
1V to power supply voltage – 0.5V
1A
90% typical
0 to 1.25V
FR-4 PCB
−10°C to 85°C
25mm × 14mm × 5.5mm
Output Pin Description
Pin 1, GND, the signal and power ground. Connect the negative power supply terminal to this pin.
Pin 2, VPSPR, the power supply positive input. Connect the positive power supply terminal to this pin. When
using this pin, the power supply current will be monitored (See Pin 7) and the controller will be
turned off when the current exceeds 2.27A. The current sense resistor is of 0.022Ω.
Pin 3, VPSDR, the power supply positive input. Connect the positive power supply terminal to this pin. When
using this pin, the power supply current will not be monitored and the controller will not be
turned off when the power supply current exceeds 2.27A. The efficiency will be higher by using
this pin since the power supply current does not go through the 0.022Ω resistor, as opposed to
using Pin 2.
Pin 4, LIS,
analog input control voltage. Setting this voltage by using a POT (Potentiometer) or a DAC
from 0 to 1.25V will set the output current from 0 to 1A. The input impedance of this pin is
100KΩ. Leaving this pin float will allow the POT on the PCB to set the output current which
sets the output current from 0 to 1A, turning clock-wise to increase the current.
Pin 5, 2.5V, analog output, reference voltage, 20ppm/°C, ± 1mA.
Pin 6, SDNG, digital input, shut down negative logic, 0 to 0.8V = shut down; 2V to 5V = turn on. Leaving this
pin open will enable the controller.
Pin 7, PSIO,
analog output, power supply current indication. It will be effective when connecting the positive
power supply terminal through VPSPR (Pin 2).
Power supply current = [voltage at PSIO]*0.91. For example, when the output voltage is 2V,
the power supply current = 2*0.91 = 1.82A.
Pin 8, LEDA, analog output for LED anode. Connect this pin to the LED positive terminal, the anode.
Pin 9, GND, power ground, connect this pin to the LED negative terminal, the cathode.
550 E. Weddell Drive, Suite 4, Sunnyvale, CA 94089. U. S. A. Tel.: (408) 747-9760, Fax: (408) 747-9770. www.analogtechnologies.com
© Copyright 1999 – 2003, Analog Technologies, Inc. All Rights Reserved. Updated: 4/28/03
1/3
Free Datasheet http://www.datasheet4u.com/
1 page | ||
| Páginas | Total 3 Páginas | |
| PDF Descargar | [ Datasheet LED22V1A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LED22V1A | HIGH EFFICIENCY LED CONTROLLER | Analog Technologies |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |