DataSheet.es    


PDF GL-8FUIB Data sheet ( Hoja de datos )

Número de pieza GL-8FUIB
Descripción Low Price & Compact Inductive Proximity Sensor
Fabricantes ETC 
Logotipo ETC Logotipo



Hay una vista previa y un enlace de descarga de GL-8FUIB (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! GL-8FUIB Hoja de datos, Descripción, Manual

GL-8/8U SERIES
Low Price & Compact Inductive Proximity Sensor Amplifier Built-in
2-wire type Different freq.
available type available
Wide variety!
Low price!
Conforming to
EMC Directive
Low price
The GL-8/8U series satisfies the need
for a low price inductive proximity
sensor. It is recommended to large
volume users for cost reduction.
The GL-8/8U series is available in
units of ten sensors.
Easy handling DC 3-wire type
Compared with the DC 2-wire type,
there are no restrictions to connection
device input conditions when wiring.
Energy-efficient and wire-saving DC 2-wire type
Its electric current consumption is just
0.8 mA or less and the wiring workload
is reduced by about 30 %.
In case 100 Nos.
are wired
300 Nos.
30 % approx.
down
200 Nos.
DC 3-wire DC 2-wire
Wide variety
A wide variety of 16 types, front
sensing type / top sensing type,
normally open type / normally closed
type, as well as, different frequency
type which allows close mounting of
sensors, is available.
Equipped with operation indicator
The GL-8/8U series is equipped with
an operation indicator (orange) for
operation confirmation.
Waterproof
Since the sensor has IP67 protection,
it can withstand water splashes.
Front sensing type
Operation indicator
(Orange)
Top sensing type
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Free Datasheet http://www.datasheet4u.com/

1 page




GL-8FUIB pdf
GL-8/8U
SENSING CHARACTERISTICS (TYPICAL)
Sensing field
4
0.157
Standard sensing object Iron sheet
15ן15ןt 1 mm 0.591ן0.591ןt 0.039 in
3
0.118
#
Front L
#
sensing Top sensing
L
2 Standard sensing object
0.079 Iron sheet
15ן15ןt 1 mm
0.591ן0.591ןt 0.039 in
1
0.039
Correlation between sensing object size and sensing range
4 Sensing object Sensing object
0.157 aןa mm aןa in aןa mm aןa in
L
3
0.118
Front
sensing
2
t 1 mm
t 0.039 in L
t 1 mm
t 0.039 in
Top sensing
Iron
Stainless steel
(SUS304)
0.079
Brass
As the sensing object size becomes smaller than
the standard size (iron sheet 15ן15ןt 1 mm
0.591ן0.591ןt 0.039 in), the sensing range
shortens as shown in the left figure.
1 Aluminum
0.039
0
10
0.394
5 0 5 10
0.197
0.197 0.394
Left Center Right
Operating point ?(mm in)
0
5 10 15
0.197 0.394 0.591
Sensing object side
length a (mm in)
20
0.787
PRECAUTIONS FOR PROPER USE
Refer to p.1152l for general precautions.
This product is not a safety sensor. Its use is not
intended or designed to protect life and prevent body
injury or property damage from dangerous parts of
machinery. It is a normal object detection sensor.
Mounting
Make sure to mount with an
M3 (length 12 mm 0.472 in
or more) truss head screw
with a tightening torque of
0.5 Nm or less.
Do not use a flat head
( )screw or a pan head
screw.
M3 (length 12 mm 0.472 in)
truss head screw
( )Accessory for
MS-GL8؂10
MS-GL8؂10 (Optional)
M3ן0.5 mm 0.020 in tapped hole
(Depth: 8 mm 0.315 in or more)
or "3.4 mm "0.134 in thru-hole
11.5 mm 0.453 in
"2.4 "0.094 in hole
(Depth: 3 mm 0.118 in or more)
If mounting using nut
and washers
( )Accessory for
MS-GL8؂10
Influence of surrounding metal
When there is a metal near the sensor, keep the minimum
separation distance specified below.
GL-8F؂10, GL-8FU؂10
8 mm
0.315 in
Metal
Metal
Metal
3 mm
0.118 in
3 mm
0.118 in
GL-8H؂10, GL-8HU؂10
Metal
Metal
3 mm 0.118 in
10 mm
0.394 in
3 mm
0.118 in
Metal
3 mm
0.118 in
3 mm
0.118 in
Mutual interference prevention
When two or more sensors are installed in parallel or face
to face, keep the minimum separation distance specified
below to avoid mutual interference.
GL-8F؂10, GL-8FU؂10
AB
AA
B
Between I
type and non
GL-8FⅪ؂10, Itype
0 mm 15 mm
(Note 2) 0.591 in
GL-8FUⅪ؂10 Between two
Itypes or two
non Itypes
20 mm 40 mm
0.787 in 1.575 in
GL-8H؂10, GL-8HU؂10
AB
Between I
type and non
GL-8HⅪ؂10, Itype
0 mm 15 mm
(Note 2) 0.591 in
GL-8HUⅪ؂10 Between two
Itypes or two
non Itypes
25 mm 40 mm
0.984 in 1.575 in
Notes: 1) Iin the model No. specifies the
different frequency type.
Notes: 2) Close mounting is possible for up to
two sensors. When mounting three
sensors or more, at an equal
spacing, in a row, the minimum
value of dimension Ashould be as
given below.
Notes: 2) GL-8FⅪ؂10, GL-8FUⅪ؂10: 6 mm 0.236 in
GL-8HⅪ؂10, GL-8HUⅪ؂10: 8.5 mm 0.335 in
Sensing range
The sensing range is Correction coefficient
specified for the
standard sensing
object (iron sheet
15 ן 15 ן t 1 mm
Model No.
Metal
Iron sheet
All models
1
0 . 5 9 1 ן 0 . 5 9 1 ן Stainless Steel
t 0.039 in).
(SUS304)
0.80 approx.
With a non-ferrous Brass
metal, the sensing
range is obtained by Aluminum
0.54 approx.
0.52 approx.
multiplying with the
correction coefficient specified on the right.
Further, the sensing range also changes if the sensing
object is smaller than the standard sensing object (iron
sheet 15ן15ןt 1 mm 0.591ן0.591ןt 0.039 in) or if the
sensing object is plated.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet GL-8FUIB.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
GL-8FUILow Price & Compact Inductive Proximity SensorETC
ETC
GL-8FUIBLow Price & Compact Inductive Proximity SensorETC
ETC

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar