DataSheet.es    


PDF SAMD20G Data sheet ( Hoja de datos )

Número de pieza SAMD20G
Descripción SMART ARM-Based Microcontroller
Fabricantes ATMEL Corporation 
Logotipo ATMEL Corporation Logotipo



Hay una vista previa y un enlace de descarga de SAMD20G (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! SAMD20G Hoja de datos, Descripción, Manual

Atmel SAM D20J / SAM D20G / SAM D20E
SMART ARM-Based Microcontroller
DATASHEET
Description
The Atmel® | SMARTSAM D20 is a series of low-power microcontrollers using the 32-bit
ARM® Cortex®-M0+ processor, and ranging from 32- to 64-pins with up to 256KB Flash and
32KB of SRAM. The SAM D20 devices operate at a maximum frequency of 48MHz and
reach 2.14 Coremark/MHz. They are designed for simple and intuitive migration with
identical peripheral modules, hex compatible code, identical linear address map and pin
compatible migration paths between all devices in the product series. All devices include
intelligent and flexible peripherals, Atmel Event System for inter-peripheral signaling, and
support for capacitive touch button, slider and wheel user interfaces.
The Atmel | SMART SAM D20 devices provide the following features: In-system
programmable Flash, eight-channel Event System, programmable interrupt controller, up to
52 programmable I/O pins, 32-bit real-time clock and calendar, up to eight 16-bit
Timer/Counters (TC). The timer/counters can be configured to perform frequency and
waveform generation, program execution timing or input capture with time and frequency
measurement of digital signals. The TCs can operate in 8- or 16-bit mode, or be cascaded
to form a 32-bit TC. The series provide up to six Serial Communication Modules (SERCOM)
that each can be configured to act as an USART, UART, SPI and I2C up to 400kHz; up to
twenty-channel 350ksps 12-bit ADC with programmable gain and optional oversampling
and decimation supporting up to 16-bit resolution, one 10-bit 350ksps DAC, two analog
comparators with window mode, Peripheral Touch Controller supporting up to 256 buttons,
sliders, wheels, and proximity sensing; programmable Watchdog Timer, brown-out detector
and power-on reset, and two-pin Serial Wire Debug (SWD) program and debug interface.
All devices have accurate and low-power external and internal oscillators. All oscillators can
be used as a source for the system clock. Different clock domains can be independently
configured to run at different frequencies while enabling power saving by running each
peripheral at its optimal clock frequency.
The Atmel | SMART SAM D20 devices have two software-selectable sleep modes, idle and
standby. In idle mode the CPU is stopped while all other functions can be kept running. In
standby all clocks and functions are stopped expect those selected to continue running. The
device supports SleepWalking. This feature allows the peripheral to wake up from sleep
based on predefined conditions, and thus allows the CPU to wake up only when needed,
e.g. when a threshold is crossed or a result is ready. The Event System supports
synchronous and asynchronous events, allowing peripherals to receive, react to and send
events even in standby mode.
The Flash program memory can be reprogrammed in-system through the SWD interface.
The same interface can be used for non-intrusive on-chip debug of application code. A boot
loader running in the device can use any communication interface to download and upgrade
the application program in the Flash memory.
The Atmel | SMART SAM D20 devices are supported with a full suite of program and system
development tools, including C compilers, macro assemblers, program
debugger/simulators, programmers and evaluation kits.
SMART
Atmel-42129N–SAM-D20_datasheet–01/2015

1 page




SAMD20G pdf
Ordering Code
ATSAMD20E15A-AU
ATSAMD20E15A-AN
ATSAMD20E15A-AUT
ATSAMD20E15A-ANT
ATSAMD20E15A-MU
ATSAMD20E15A-MN
ATSAMD20E15A-MUT
ATSAMD20E15A-MNT
ATSAMD20E16A-AU
ATSAMD20E16A-AN
ATSAMD20E16A-AUT
ATSAMD20E16A-ANT
ATSAMD20E16A-MU
ATSAMD20E16A-MN
ATSAMD20E16A-MUT
ATSAMD20E16A-MNT
ATSAMD20E17A-AU
ATSAMD20E17A-AN
ATSAMD20E17A-AUT
ATSAMD20E17A-ANT
ATSAMD20E17A-MU
ATSAMD20E17A-MN
ATSAMD20E17A-MUT
ATSAMD20E17A-MNT
ATSAMD20E18A-AU
ATSAMD20E18A-AN
ATSAMD20E18A-AUT
ATSAMD20E18A-ANT
ATSAMD20E18A-MU
ATSAMD20E18A-MN
ATSAMD20E18A-MUT
ATSAMD20E18A-MNT
FLASH (bytes)
SRAM (bytes)
32K 4K
64K 8K
128K
16K
256K
32K
Package
TQFP32
QFN32
TQFP32
QFN32
TQFP32
QFN32
TQFP32
QFN32
Carrier Type
Tray
Tape & Reel
Tray
Tape & Reel
Tray
Tape & Reel
Tray
Tape & Reel
Tray
Tape & Reel
Tray
Tape & Reel
Tray
Tape & Reel
Tray
Tape & Reel
Atmel | SMART SAM D20 [DATASHEET]
Atmel-42129N–SAM-D20_datasheet–01/2015
5

5 Page





SAMD20G arduino
4. Pinout
4.1 SAM D20J
4.1.1 QFP64
PA00
PA01
PA02
PA03
PB04
PB05
GNDANA
VDDANA
PB06
PB07
PB08
PB09
PA04
PA05
PA06
PA07
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
48 VDDIO
47 GND
46 PA25
45 PA24
44 PA23
43 PA22
42 PA21
41 PA20
40 PB17
39 PB16
38 PA19
37 PA18
36 PA17
35 PA16
34 VDDIO
33 GND
DIGITAL PIN
ANALOG PIN
OSCILLATOR
GROUND
INPUT SUPPLY
REGULATED OUTPUT SUPPLY
RESET PIN
Atmel | SMART SAM D20 [DATASHEET]
Atmel-42129N–SAM-D20_datasheet–01/2015
11

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet SAMD20G.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
SAMD20ESMART ARM-Based MicrocontrollerATMEL Corporation
ATMEL Corporation
SAMD20GSMART ARM-Based MicrocontrollerATMEL Corporation
ATMEL Corporation
SAMD20JSMART ARM-Based MicrocontrollerATMEL Corporation
ATMEL Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar