DataSheet.es    


PDF TS1002 Data sheet ( Hoja de datos )

Número de pieza TS1002
Descripción (TS1002 / TS1004) THE ONLY 0.8V/0.6uA RAIL-TO-RAIL DUAL/QUAD OP AMPS
Fabricantes Touchstone Semiconductor 
Logotipo Touchstone Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de TS1002 (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! TS1002 Hoja de datos, Descripción, Manual

TS1002/TS1004
THE ONLY 0.8V/0.6µA RAIL-TO-RAIL DUAL/QUAD OP AMPS
FEATURES
Single 0.65V to 2.5V Operation
Supply current: 0.6μA per amplifier (typ)
Offset voltage: 0.5mV (typ)
Low TCVOS: 10µV/°C (typ)
AVOL Driving 100kΩ Load: 90dB (min)
Unity Gain Stable
Rail-to-rail Input and Output
No Output Phase Reversal
Packaging: TS1002 8-pin MSOP
TS1004 14-pin TSSOP
APPLICATIONS
Battery/Solar-Powered Instrumentation
Portable Gas Monitors
Low-voltage Signal Processing
Nanopower Active Filters
Wireless Remote Sensors
Battery-powered Industrial Sensors
Active RFID Readers
Powerline or Battery Current Sensing
Handheld/Portable POS Terminals
DESCRIPTION
The TS1002 and the TS1004 are the industry’s first
and only dual and quad single-supply, precision
CMOS operational amplifiers fully specified to operate
at 0.8V while consuming less than 0.6µA supply
current per amplifier. Optimized for ultra-long-life
battery-powered applications, the TS1002 and the
TS1004 join Touchstone’s TS1001 operational
amplifier in the “NanoWatt Analog™” high-
performance analog integrated circuits portfolio. Both
op amps exhibit a typical offset voltage of 0.5mV, a
typical input bias current of 25pA, and rail-to-rail input
and output stages. The TS1002 and the TS1004 can
operate from single-supply voltages from 0.65V to
2.5V.
The TS1002/TS1004’s combined features make
either an excellent choice in applications where very
low supply current and low operating supply voltage
translate into very long equipment operating time.
Applications include: nanopower active filters,
wireless remote sensors, battery and powerline
current sensors, portable gas monitors, and
handheld/portable POS terminals.
The TS1002 and the TS1004 are fully specified at
VDD = 0.8V and over the industrial temperaturehttp://www.DataSheet4U.net/
range (−40°C to +85°C). The TS1002 is available in
PCB-space saving 8-lead MSOP surface-mount
packages. The TS1004 is available in a 14-pin
TSSOP package.
TYPICAL APPLICATION CIRCUIT
30%
25%
Supply Current Distribution
VDD = 0.8V
20%
15%
10%
A NanoWatt 2-Pole Sallen-Key Low-Pass Filter
Patent(s) Pending
NanoWatt Analog and the Touchstone Semiconductor logo are registered
trademarks of Touchstone Semiconductor, Incorporated.
5%
0%
0.53 0.58 0.63 0.68 0.73
Supply Current per Amplifier - µA
Page 1
© 2012 Touchstone Semiconductor, Inc. All rights reserved.
datasheet pdf - http://www.DataSheet4U.net/

1 page




TS1002 pdf
TS1002/TS1004
TYPICAL PERFORMANCE CHARACTERISTICS
Input Bias Current (IIN+, IIN-) vs Input Common-Mode Voltage
100
VDD =0.8V
75 TA = +25°C
Input Bias Current (IIN+, IIN-) vs Input Common-Mode Voltage
250
VDD = 2.5V
200 TA = +25°C
50
25
0
-25
-50
0
0.2 0.4 0.6 0.8
INPUT COMMON-MODE VOLTAGE - Volt
150
100
50
0
-50
0 0.5 1 1.5 2 2.5
INPUT COMMON-MODE VOLTAGE - Volt
Output Voltage High (VOH) vs Temperature, RLOAD =100k
4.5
4 RL = 100k
3.5 VDD = 2.5V
3
2.5
2
1.5 VDD = 0.8V
1
0.5
0
-40 +25 +85
TEMPERATURE - °C
Output Voltage Low (VOL) vs Temperature, RLOAD =100k
1.8
1.6
1.4 VDD = 2.5V
1.2
http://www.DataSheet4U.net/
1
0.8
0.6
0.4 VDD = 0.8V
0.2 RL = 100k
0
-40
+25
+85
TEMPERATURE - °C
Output Voltage High (VOH) vs Temperature, RLOAD =10k
35
30 RL = 10k
25 VDD = 2.5V
20
15
VDD = 0.8V
10
5
0
-40
+25
TEMPERATURE - °C
TS1002_4DS r1p0
+85
Output Voltage Low (VOL) vs Temperature, RLOAD =10k
20
16 VDD = 2.5V
12
8
VDD = 0.8V
4
RL = 10k
0
-40
+25
TEMPERATURE - °C
+85
Page 5
RTFDS
datasheet pdf - http://www.DataSheet4U.net/

5 Page





TS1002 arduino
Printed Circuit Board Layout Considerations
Even though these amplifiers operate from a single
0.65V to 2.5V power supply and consume very little
supply current, it is always good engineering
practice to bypass the power supplies pins with a
0.1μF ceramic capacitor placed in close proximity to
the VDD and VSS (or GND) pins.
Good pcb layout techniques and analog ground
plane management improve the performance of any
analog circuit by decreasing the amount of stray
TS1002/TS1004
capacitance that could be introduced at the op amp's
inputs and outputs. Excess stray capacitance can
easily couple noise into the input leads of the op
amp and excess stray capacitance at the output will
add to any external capacitive load. Therefore, PC
board trace lengths and external component leads
should be kept a short as practical to any of the
amplifiers’ package pins. Second, it is also good
engineering practice to route/remove any analog
ground plane from the inputs and the output pins of
these amplifiers.
http://www.DataSheet4U.net/
TS1002_4DS r1p0
Page 11
RTFDS
datasheet pdf - http://www.DataSheet4U.net/

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet TS1002.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TS1001RAIL-TO-RAIL OP AMPTouchstone
Touchstone
TS1001RAIL-TO-RAIL OP AMPSilicon Laboratories
Silicon Laboratories
TS1002(TS1002 / TS1004) THE ONLY 0.8V/0.6uA RAIL-TO-RAIL DUAL/QUAD OP AMPSTouchstone Semiconductor
Touchstone Semiconductor
TS1002THE ONLY 0.8V/0.6uA RAIL-TO-RAIL DUAL/QUAD OP AMPSSilicon Laboratories
Silicon Laboratories

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar