|
|
PDF 25Q16BV Data sheet ( Hoja de datos )
| Número de pieza | 25Q16BV | |
| Descripción | W25Q16BV | |
| Fabricantes | WINBOND | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 25Q16BV (archivo pdf) en la parte inferior de esta página. Total 68 Páginas | ||
|
No Preview Available !
W25Q16BV
16M-BIT
SERIAL FLASH MEMORY WITH
DUAL AND QUAD SPI
http://www.DataSheet4U.net/
-1-
Publication Release Date: July 08, 2010
Revision F
datasheet pdf - http://www.DataSheet4U.net/
1 page  
W25Q16BV
1. GENERAL DESCRIPTION
The W25Q16BV (16M-bit) Serial Flash memory provides a storage solution for systems with limited
space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial
Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI
(XIP) and storing voice, text and data. The devices operate on a single 2.7V to 3.6V power supply with
current consumption as low as 4mA active and 1µA for power-down. All devices are offered in space-
saving packages.
The W25Q16BV array is organized into 8,192 programmable pages of 256-bytes each. Up to 256 bytes
can be programmed at a time. Pages can be erased in groups of 16 (sector erase), groups of 128 (32KB
block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q16BV has 512
erasable sectors and 32 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in
applications that require data and parameter storage. (See figure 2.)
The W25Q16BV supports the standard Serial Peripheral Interface (SPI), and a high performance
Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1
(DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing
equivalent clock rates of 208MHz for Dual Output and 416MHz for Quad Output when using the Fast
Read Dual/Quad Output instructions. These transfer rates can outperform standard Asynchronous 8 and
16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as
few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place)
operation.
A Hold pin, Write Protect pin and programmable write protection, with top or bottom array control,
provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and
device identification with a 64-bit Unique Serial Number.
2. FEATURES
http://www.DataSheet4U.net/
• Family of SpiFlash Memories
– W25Q16BV: 16M-bit / 2M-byte (2,097,152)
– 256-bytes per programmable page
• Standard, Dual or Quad SPI
– Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
– Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
• Highest Performance Serial Flash
– Up to 8X that of ordinary Serial Flash
– 104MHz clock operation
– 208MHz equivalent Dual SPI
– 416MHz equivalent Quad SPI
– 50MB/S continuous data transfer rate
• Efficient “Continuous Read Mode”
– Low Instruction overhead
– As few as 8 clocks to address memory
– Allows true XIP (execute in place) operation
– Outperforms X16 Parallel Flash
• Low Power, Wide Temperature Range
– Single 2.7 to 3.6V supply
– 4mA active current, <1µA Power-down (typ.)
– -40°C to +85°C operating range
• Flexible Architecture with 4KB sectors
– Uniform Sector Erase (4K-bytes)
– Block Erase (32K and 64K-bytes)
– Program one to 256 bytes
– More than 100,000 erase/write cycles
– More than 20-year data retention
• Advanced Security Features
– Software and Hardware Write-Protect
– Top or Bottom, Sector or Block selection
– Lock-Down and OTP protection(1)
– 64-Bit Unique ID for each device
•
–
Space Efficient Packaging
8-pin SOIC 150(2)/208-mil
– 8-pad WSON 6x5-mm
– 8-pin PDIP 300-mil(2)
– 16-pin SOIC 300-mil(2)
– Contact Winbond for KGD and other options
Notes 1. Refer to Ordering Information.
2. These package types are Special Order Only, please contact Winbond for more information.
-5-
Publication Release Date: July 08, 2010
Revision F
datasheet pdf - http://www.DataSheet4U.net/
5 Page 
W25Q16BV
10. FUNCTIONAL DESCRIPTION
10.1 SPI OPERATIONS
10.1.1 Standard SPI Instructions
The W25Q16BV is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and
Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is
not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the falling and
rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising edges of /CS.
10.1.2 Dual SPI Instructions
The W25Q16BV supports Dual SPI operation when using the “Fast Read Dual Output and Dual I/O” (3B
and BB hex) instructions. These instructions allow data to be transferred to or from the device at two to
three times the rate of ordinary Serial Flash devices. The Dual Read instructions are ideal for quickly
downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical code
directly from the SPI bus (XIP). When using Dual SPI instructions the DI and DO pins become
bidirectional I/O pins: IO0 and IO1.
10.1.3 Quad SPI Instructions
The W25Q16BV supports Quad SPI operation when usinghttp://www.DataSheet4U.net/ the “Fast Read Quad Output”, “Fast Read
Quad I/O”, “Word Read Quad I/O” and “Octal Word Quad I/O” (6B, EB, E7 and E3 hex respectively).
These instructions allow data to be transferred to or from the device four to six times the rate of ordinary
Serial Flash. The Quad Read instructions offer a significant improvement in continuous and random
access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP).
When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP
and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad
Enable bit (QE) in Status Register-2 to be set.
10.1.4 Hold Function
The /HOLD signal allows the W25Q16BV operation to be paused while it is actively selected (when /CS is
low). The /HOLD function may be useful in cases where the SPI data and clock signals are shared with
other devices. For example, consider if the page buffer was only partially written when a priority interrupt
requires use of the SPI bus. In this case the /HOLD function can save the state of the instruction and the
data in the buffer so programming can resume where it left off once the bus is available again. The
/HOLD function is only available for standard SPI and Dual SPI operation, not during Quad SPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data
Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip
Select (/CS) signal should be kept active (low) for the full duration of the /HOLD operation to avoid
resetting the internal logic state of the device.
- 11 -
Publication Release Date: July 08, 2010
Revision F
datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 68 Páginas | |
| PDF Descargar | [ Datasheet 25Q16BV.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 25Q16BSIG | Uniform Sector Dual and Quad Serial Flash |  GigaDevice |
| 25Q16BV | W25Q16BV | WINBOND |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |