PDF ICX085AL Data sheet ( Hoja de datos )

Número de pieza	ICX085AL
Descripción	CCD Image Sensor
Fabricantes	Sony
Logotipo
Hay una vista previa y un enlace de descarga de ICX085AL (archivo pdf) en la parte inferior de esta página. Total 20 Páginas
No Preview Available ! ICX085AL Diagonal 11mm (Type 2/3) Progressive Scan CCD Image Sensor with Square Pixel for B/W Cameras Description The ICX085AL is a diagonal 11mm (Type 2/3) interline CCD solid-state image sensor with a square pixel array. Progressive scan allows all pixels signals to be output independently within approximately 1/12 second. This chip features an electronic shutter with variable charge-storage time which makes it possible to realize full-frame still image without a mechanical shutter. High sensitivity and low dark current are achieved through the adoption of HAD (Hole-Accumulation Diode) sensors. This chip is suitable for image input applications such as still cameras which require high resolution. Features • Progressive scan allows individual readout of the image signals from all pixels. • High vertical resolution (1024TV-lines) still image without a mechanical shutter. • Square pixel unit cell • Aspect ratio 5:4 • Horizontal drive frequency: 20.25MHz • Reset gate bias is not adjusted. • Substrate voltage: 5.5 to 12.5V • Continuous variable-speed shutter • High resolution, high sensitivity, low dark current • Low smear • Excellent antiblooming characteristics • Horizontal register: 5V drive http://www.DataSheet4U.net/ 20 pin DIP (Ceramic) Pin 1 1 V 4 Pin 11 H 3 56 Optical black position (Top View) Device Structure • Interline CCD image sensor • Image size: Diagonal 11mm (Type 2/3) • Number of effective pixels: 1300 (H) x 1030 (V) approx. 1.3M pixels • Total number of pixels: 1360 (H) x 1034 (V) approx. 1.4M pixels • Chip size: 10.0mm (H) x 8.7mm (V) • Unit cell size: 6.7µm (H) x 6.7µm (V) • Optical black: Horizontal (H) direction: Front 4 pixels, rear 56 pixels Vertical (V) direction: Front 3 pixels, rear 1 pixel • Number of dummy bits: Horizontal 24 Vertical 1 • Substrate material: Silicon Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E95Z10D99 datasheet pdf - http://www.DataSheet4U.net/ 1 page ICX085AL Clock Equivalent Circuit Constant Item Capacitance between vertical transfer clock and GND Capacitance between vertical transfer clocks Capacitance between horizontal transfer clock and GND Capacitance between horizontal transfer clocks Symbol CφV1 CφV2, CφV3 CφV12 CφV23 CφV31 CφH1 CφH2 CφHH Min. Typ. Max. Unit Remarks 5000 pF 10000 pF 1200 pF 100 pF 3300 pF 82 pF 68 pF 22 pF Capacitance between reset gate clock and GND CφRG 6 pF Capacitance between substrate clock and GND CφSUB Vertical transfer clock series resistor Vertical transfer clock ground resistor Horizontal transfer clock series resistor Reset gate clock series resistor R1, R2, R3 RGND RφH1, RφH2 RφRG 800 pF 30 Ω 30 Ω 10 Ω 20 Ω Vφ1 R1 CφV12 R2 Vφ2 http://www.DataSheet4U.net/ CφV1 CφV2 RGND Cφv31 CφV3 Cφv23 RφH1 Hφ1 CφH1 CφHH RφH2 Hφ2 CφH2 R3 Vφ3 Vertical transfer clock equivalent circuit RGφ RφRG CφRG Horizontal transfer clock equivalent circuit Reset gate clock equivalent circuit –5– datasheet pdf - http://www.DataSheet4U.net/ 5 Page ICX085AL 4. Video signal shading Set to standard imaging condition II. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity so that the average value of the signal output is 150mV. Then measure the maximum (Vmax [mV]) and minimum (Vmin [mV]) values of the signal output and substitute the values into the following formula. SH = (Vmax – Vmin)/150 x 100 [%] 5. Dark signal Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60°C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference. 6. Dark signal shading After measuring 5, measure the maximum (Vdmax [mV]) and minimum (Vdmin [mV]) values of the dark signal output and substitute the values into the following formula. ∆Vdt=Vdmax – Vdmin [mV] 7. Lag Adjust the signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) x 100 [%] FLD http://www.DataSheet4U.net/ SG Strobe light timing Output Light Signal output 150mV Vlag (Lag) – 11 – datasheet pdf - http://www.DataSheet4U.net/ 11 Page

Páginas	Total 20 Páginas
PDF Descargar	[ Datasheet ICX085AL.PDF ]

Hoja de datos destacado

Número de pieza	Descripción	Fabricantes
ICX085AK	CCD Image Sensor	Sony
ICX085AL	CCD Image Sensor	Sony

Número de pieza	Descripción	Fabricantes
SLA6805M	High Voltage 3 phase Motor Driver IC.	Sanken
SDC1742	12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.	Analog Devices

DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar