DataSheet.es    


PDF ICX080AK Data sheet ( Hoja de datos )

Número de pieza ICX080AK
Descripción CCD Image Sensor
Fabricantes Sony 
Logotipo Sony Logotipo



Hay una vista previa y un enlace de descarga de ICX080AK (archivo pdf) en la parte inferior de esta página.


Total 19 Páginas

No Preview Available ! ICX080AK Hoja de datos, Descripción, Manual

ICX080AK
Diagonal 6mm (Type 1/3) CCD Image Sensor for NTSC Color Video Cameras
Description
The ICX080AK is an interline CCD solid-state
image sensor suitable for NTSC color video
cameras. This chip conforms to DV standard SD
mode, and has the optimal number of pixels for
MPEG2 Main level. While achieving a horizontal
resolution of 450 TV lines, the area has been
expanded 33% in both vertical and horizontal
directions, making the chip suitable for electronic
vibration stabilizer and electronic panning/tilting. In
addition, complete 16:9 wide aspect ratio images
are provided with a high picture quality without
requiring vertical interpolation.
High sensitivity and low dark current are achieved
through the adoption of Ye, Cy, Mg and G
complementary color mosaic filters and HAD (Hole-
Accumulation Diode) sensors.
This chip features a field period readout system
and an electronic shutter with variable charge-
storage time.
The package is a 16-pin DIP (Plastic), and both
top and bottom surface reference can be assured at
the same time.
16 pin DIP (Plastic)
V
4
Pin 9
Pin 1
8
12
H 50
Features
Supports electronic vibration stabilizer and electronic panning/tilting
(33%/one side)
Optical black position
(Top View)
Supports electronic zoom
http://www.DataSheet4U.net/
Supports DV standard SD mode and MPEG2 Main level (13.5MHz)
Supports 16:9 wide aspect ratio (for both 18MHz and 5fsc)
Supply voltage: 12V
Horizontal register and reset gate: 2.7 to 3.6V drive
No voltage adjustment (Reset gate and substrate bias are not adjusted.)
High resolution, high sensitivity, low dark current and low smear
Excellent antiblooming characteristics
Continuous variable-speed shutter (1/60 to 1/10000s)
Supports short exit pupil distance (Recommended range: –20 to –100mm)
Ye, Cy, Mg and G complementary color mosaic filters on chip
16-pin high precision plastic package (both top and bottom surface reference possible)
Device Structure
Interline CCD image sensor
Image size:
Total number of pixels:
Total number of effective pixels:
Number of effective pixels: 4:3 NTSC:
16:9 18MHz:
16:9 5fsc:
Chip size:
Unit cell size:
Optical black:
Number of dummy bits:
Substrate material:
Diagonal 6mm (Type 1/3)
1016 (H) x 674 (V) approx. 680K pixels
962 (H) x 654 (V) approx. 630K pixels
711 (H) x 485 (V) approx. 340K pixels
948 (H) x 485 (V) approx. 460K pixels
942 (H) x 485 (V) approx. 460K pixels
5.90mm (H) x 4.92mm (V)
5.05µm (H) x 5.55µm (V)
Horizontal (H) direction: Front 4 pixels, rear 50 pixels
Vertical (V) direction: Front 12 pixels, rear 8 pixels
Horizontal 28
Vertical 1 (even fields only)
Silicon
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E95518D99
datasheet pdf - http://www.DataSheet4U.net/

1 page




ICX080AK pdf
ICX080AK
Drive Clock Waveform Conditions
(1) Readout clock waveform
100%
90%
II II
10%
0%
tr
(2) Vertical transfer clock waveform
Vφ1
VVT
twh
tf
Vφ3
φM
φM
2
0V
VVH1
VVHH
VVH
VVHH
VVHL
VVHL
VVHL
VVHH
VVHH
VVH3
VVHL
VVH
VVL1
VVLH
VVLL
VVL
Vφ2
VVHH
VVH2 VVHL
VVHH
VVH
VVHL
VVL3
http://www.DataSheet4U.net/
VVL
Vφ4
VVH
VVHH
VVLL
VVLH
VVHH
VVHL
VVHL
VVH4
VVL2VVLH
VVLL
VVL
VVH = (VVH1 + VVH2)/2
VVL = (VVL3 + VVL4)/2
VφV = VVHn – VVLn (n = 1 to 4)
VVLH
VVLL
VVL4
–5–
VVL
datasheet pdf - http://www.DataSheet4U.net/

5 Page





ICX080AK arduino
ICX080AK
6. Dark signal
Measure the average value of the Y signal output (Ydt [mV]) with the device ambient temperature 60°C
and the device in the light-obstructed state, using the horizontal idle transfer level as a reference.
7. Dark signal shading
After measuring 6, measure the maximum (Ydmax [mV]) and minimum (Ydmin [mV]) values of the Y
signal output and substitute the values into the following formula.
Ydt = Ydmax – Ydmin [mV]
8. Flicker
1) Fy
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y
signal output is 200mV, and then measure the difference in the signal level between fields (Yf [mV]).
Then substitute the value into the following formula.
Fy = (Yf/200) x 100 [%]
2) Fcr, Fcb
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y
signal output is 200mV, insert an R and B filter, and then measure both the difference in the signal level
between fields of the chroma signal (Cr, Cb) as well as the average value of the chroma signal output
(CAr, CAb). Substitute the values into the following formula.
Fci = (Ci/CAi) x 100 [%] (i = r, b)
9. Line crawls
Set to standard imaging condition II. Adjust the luminoushttp://www.DataSheet4U.net/ intensity so that the average value of the Y
signal output is 200mV, and then insert a white subject and R, G, and B filters and measure the difference
between Y signal lines for the same field (Ylw, Ylr, Ylg, Ylb [mV]). Substitute the values into the
following formula.
Lci = (Yli/200) x 100 [%] (i = w, r, g, b)
10. Lag
Adjust the Y signal output value generated by strobe light to 200mV. After setting the strobe light so that it
strobes with the following timing, measure the residual signal (Ylag). Substitute the value into the
following formula.
Lag = (Ylag/200) x 100 [%]
VD
Strobe light timing
Light
Output
Y signal output 200mV Ylag (lag)
– 11 –
datasheet pdf - http://www.DataSheet4U.net/

11 Page







PáginasTotal 19 Páginas
PDF Descargar[ Datasheet ICX080AK.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ICX080AKCCD Image SensorSony
Sony

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar