|
|
PDF SF2006C Data sheet ( Hoja de datos )
| Número de pieza | SF2006C | |
| Descripción | SAW Filter | |
| Fabricantes | RF Monolithics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SF2006C (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
• SAW Filter for W-CDMA
• 5.0 X 5.0 X 1.7 mm Surface-Mount Case
• Complies with Directive 2002/95/EC (RoHS) Pb
Maximum Rating
Rating
Input Power Level
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Value
10
-30 to +70
-30 to +70
Units
dBm
°C
°C
SF2006C
190.00 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss
6 dB Bandwidth
Group Delay Ripple
RMS Phase Linearity, fC ± 2 MHz
Attenuation Referended to ILMIN:
170 to 180 MHz, or (fC - 20 MHz) to (fC - 10 MHz)
180 to 185.5 MHz, or (fC -10 MHz) to (fC -4.5 MHz)
194.5 to 200 MHz, or (fC + 4.5 MHz) to (fC + 10 MHz)
200 to 210 MHz, or (fC + 10 MHz) to (fC + 20 MHz)
Ultimate Rejection
Lid Symbolization (Y=year, WW=week, S=shift)
Electrical Connections
Connection
Port 1
Input
Port 2
Output
Ground
Dot indicates Pin 1
Terminals
2
6
All others
Sym
fC
ILMIN
BW
Notes
www.DataSheet.net/
SM5050-8
Min Typ Max
190
8.0 10
4.8 5.73
70 150
68
27 34
25 31
25 30
27 33
50
RFM 734 YWWS
Units
MHz
dB
MHz
ns
deg
dB
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temper-
ature range with filter soldered to the specified demonstration board with
impedance matching to 50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the
nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the
passband. Rejection in final user application is dependent on PCB layout
and external impedance matching design. See Application Note No. 42
for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production"
and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are
subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design.
However, impedances and impedance matching may vary between Port 1
and Port 2, so that the filter must always be installed in one direction per
the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered
trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
©2008-2010 by RF Monolithics, Inc.
Page 1 of 4
SF2006C - 6/14/10
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet SF2006C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SF2006C | SAW Filter | RF Monolithics |
| SF2006G | (SF2001G - SF2008G) Glass Passivated Super Fast Rectifiers |  Taiwan Semiconductor Company |
| SF2006G | (SF2001G - SF2008G) Glass Passivated Super Fast Rectifiers |  Luguang Electronic Technology |
| SF2006G | (SF2001G - SF2008G) 20.0 Ampere Dual Unipolar-Doubler Polarity Superfast Recovery Diode |  Thinki Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |