|
|
PDF SF1133A Data sheet ( Hoja de datos )
| Número de pieza | SF1133A | |
| Descripción | SAW Filter | |
| Fabricantes | RF Monolithics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SF1133A (archivo pdf) en la parte inferior de esta página. Total 3 Páginas | ||
|
No Preview Available !
• Designed for GSM BTS Receiver IF Applications
• Compatible with National Semiconductor Chip Set
• Very Flexible Impedance Matching
• Unbalanced or Balanced Input or Output
• Complies with Directive 2002/95/EC (RoHS)
Pb
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
Suitable for lead-free soldering - Max. Soldering Profile
Value
Units
+15 dBm
30 VDC
-40 to +85
°C
260°C for 30 s
Electrical Characteristics
Characteristic
Nominal Center Frequency
Passband
Insertion Loss at fc
1 db Passband
Amplitude Ripple over fc±100 kHz
Group Delay Variation over fc ±100 kHz
Rejection
fc-800 to fc-600 and fc+600 to fc+800 kHz
fc-30 MHz to fc-800 kHz
fc+800 kHz to fc+17 MHz
fc-80 MHz to fc-30 MHz
fc+17 Mhz to fc+80 MHz
Operating Temperature Range
Sym
fC
IL
BW1
GDV
Notes
1
1, 2
www.DataSheet.net/
1, 2, 3
TA 1
Min
±100
20
30
30
35
35
-35
SF1133A
246 MHz
SAW Filter
SM9171-10
Typ
246.000
Max
7.0
1.0
500
Units
MHz
dB
kHz
dBP-P
nsP-P
dB
+85 °C
Impedance Matching to 50 Ω Unbalanced
Impedance Matching to 200 Ω Balanced
Case Style
Lid Symbolization (YY = year, WW = week)
External L-C
External L-C
SMP9171-10 9.1 x 7.1 mm Nominal Footprint
RFM SF1133A YYWW
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range
with filter soldered to the specified demonstration board with impedance matching to 50 Ω
and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center
frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband.
Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E"
indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However,
impedances and impedance matching may vary between Port 1 and Port 2, so that the fil-
ter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Electrostatic Sensitive Device. Observe precautions for handling.
Electrical Connections
Connection
Port 1 Hot
Port 1 Gnd Return
Port 2 Hot
Port 2 Gnd Return
Case Ground
Terminals
10
1
5
6
All others
RF Monolithics, Inc. Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: [email protected]
http://www.rfm.com
SF1133A-121604
Page 1 of 3
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page | ||
| Páginas | Total 3 Páginas | |
| PDF Descargar | [ Datasheet SF1133A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SF1133A | SAW Filter | RF Monolithics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |