|
|
PDF 64F2633 Data sheet ( Hoja de datos )
| Número de pieza | 64F2633 | |
| Descripción | HD64F2633 | |
| Fabricantes | Renesas Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 64F2633 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
To all our customers
Regarding the change of names mentioned in the document, such as Hitachi
Electric and Hitachi XX, to Renesas Technology Corp.
The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Hitachi, Hitachi, Ltd., Hitachi Semiconductors, and other Hitachi brand
names are mentioned in the document, these names have in fact all been changed to Renesas
Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and
corporate statement, no changes whatsoever have been made to the contents of the document, and
these changes do not constitute any alteration to the contents of the document itself.
Renesas Technology Home Page: http://www.renesas.com
www.DataSheet.net/
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page  
General Precautions on the Handling of Products
1. Treatment of NC Pins
Note:
Do not connect anything to the NC pins.
The NC (not connected) pins are either not connected to any of the internal circuitry; or
are used as test pins or to reduce noise. If something is connected to the NC pins, the
operation of the LSI is not guaranteed.
2. Treatment of Unused Input Pins
Note:
Fix all unused input pins to high or low level.
Generally, the input pins of CMOS products are high-impedance input pins. If unused pins
are in their open states, intermediate levels are induced by noise in the vicinity, a pass-
through current flows internally, and a malfunction may occur.
3. Processing before Initialization
Note:
When power is first supplied, the product’s state is undefined. The states of internal
circuits are undefined until full power is supplied throughout the chip and a low level is
input on the reset pin. During the period where the states are undefined, the register
settings and the output state of each pin are also undefined. Design your system so that it
does not malfunction because of processing while it is in this undefined state. For those
products which have a reset function, reset the LSI immediately after the power supply has
been turned on.
www.DataSheet.net/
4. Prohibition of Access to Undefined or Reserved Address
Note:
Access to undefined or reserved addresses is prohibited.
The undefined or reserved addresses may be used to expand functions, or test registers
may have been be allocated to these address. Do not access these registers: the system’s
operation is not guaranteed if they are accessed.
Datasheet pdf - http://www.DataSheet4U.co.kr/
5 Page 
Section
Page
Item
Description
4.4 Interrupts
117
Note * added
Figure 4-4 Interrupt Sources Note *3 added
and Number of Interrupts
5.1.1 Features
121
• DTC and DMAC control
Note * added
5.2.2 Interrupt Priority 125
Registers A to L, O
(IPRA to IPRL, IPRO)
Table 5-3 Correspondence
between Interrupt Sources
and IPR Settings
5.2.5 IRQ Status
Register (ISR)
128
Bits 7 to 0—IRQ7 to IRQ0 flags Note * added
(IRQ7F to IRQ0F)
(n = 5 to 0) amended to
(n = 7 to 0)
5.3.1 External
Interrupts
129
IRQ7 to IRQ0 Interrupts
IRQ5 to IRQ0 amended to
IRQ7 to IRQ0
5.3.2 Internal
Interrupts
130
Notes *1 and *2 added
5.3.3 Interrupt
Exception Handling
Vector Table
131 to 134 Table 5-4(a) Interrupt
Sources, Vector Addresses,
and Interrupt Priorities
(H8S/2633, H8S/2632,
H8S/2631, H8S/2633R)
135 to 138
www.DataSheet.net/
Table 5-4(b) Interrupt
Sources, Vector Addresses,
and Interrupt Priorities
(H8S/2695)
H8S/2633R added
Amend as follows:
Interrupt Source column:
"CMI" → "Reserved"
Origin of Interrupt Source
column: "Refresh timer" →
""
Newly added
5.6 DTC and DMAC
Activation by Interrupt
(DMAC and DTC
functions are not
available in the
H8S/2695)
150
Title amended
5.6.2 Block Diagram 151
Figure 5-9 Interrupt Control Note * added
for DTC and DMAC
5.6.3 Operation
(DMAC and DTC
functions are not
available in the
H8S/2695)
152
Table 5-11 Interrupt Source Note *1 added
Selection and Clearing Control
(4) Notes on Use
Note * added
3
Datasheet pdf - http://www.DataSheet4U.co.kr/
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet 64F2633.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 64F2633 | HD64F2633 | Renesas Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |