|
|
Número de pieza | B32776E | |
Descripción | Metallized Polypropylene Film Capacitors | |
Fabricantes | EPCOS | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de B32776E (archivo pdf) en la parte inferior de esta página. Total 21 Páginas | ||
No Preview Available ! Film Capacitors
Metallized Polypropylene Film Capacitors (MKP)
Series/Type:
Date:
B32774 ... B32778
May 2011
www.DataSheet.net/
© EPCOS AG 2011. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Datasheet pdf - http://www.DataSheet4U.co.kr/
1 page B32776
MKP DC link high density series
Ordering codes and packing units (lead spacing 37.5 mm)
CR Max. dimensions P1 Ordering code
w×h×l
(composition see
below)
µF mm
mm
VR,70 °C = 450 V DC, Vop,85 °C = 450 V DC
30 20.0 × 39.5 × 41.5 10.2 B32776G4306+000
30 20.0 × 39.5 × 41.5 B32776E4306+000
35 28.0 × 37.0 × 42.0 10.2 B32776G4356+000
35 28.0 × 37.0 × 42.0 B32776E4356+000
40 28.0 × 37.0 × 42.0 10.2 B32776G4406+000
40 28.0 × 37.0 × 42.0 B32776E4406+000
50 28.0 × 42.5 × 41.5 10.2 B32776G4506+000
50 28.0 × 42.5 × 41.5 B32776E4506+000
60 30.0 × 45.0 × 42.0 B32776E4606+000
VR,70 °C = 800 V DC, Vop,85 °C = 700 V DC
14 18.0 × 32.5 × 41.5 B32776E8146+000
15 20.0 × 39.5 × 41.5 10.2 B32776G8156+000
20 28.0 × 37.0 × 42.0 10.2 B32776G8206+000
20 28.0 × 37.0 × 42.0 B32776E8206+000
www.DataSheet.net/
22 28.0 × 37.0 × 42.0 10.2 B32776G8226+000
25 28.0 × 42.5 × 41.5 B32776E8256+000
30 30.0 × 45.0 × 42.0 20.3 B32776G8306+000
30 30.0 × 45.0 × 42.0 B32776E8306+000
VR,70 °C = 1100 V DC, Vop,85 °C = 920 V DC
12 20.0 × 39.5 × 41.5 10.2 B32776G0126+000
12 20.0 × 39.5 × 41.5 B32776E0126+000
14 28.0 × 37.0 × 42.0 10.2 B32776G0146+000
14 28.0 × 37.0 × 42.0 B32776E0146+000
16 28.0 × 42.5 × 41.5 10.2 B32776G0166+000
16 28.0 × 42.5 × 41.5 B32776E0166+000
20 30.0 × 45.0 × 42.0 20.3 B32776G0206+000
20 30.0 × 45.0 × 42.0 B32776E0206+000
IRMS,max
70 °C
10 kHz
A
12.5
11.5
13.5
12.5
14.5
13.5
16.0
15.0
16.5
10.0
10.5
12.0
11.5
13.0
13.5
15.0
14.0
11.0
10.0
13.0
12.0
13.0
12.0
15.0
13.0
IRMS,max
70 °C
20 kHz
A
11.5
10.5
12.5
11.5
13.5
12.5
15.0
14.0
15.0
9.0
9.5
11.0
10.5
12.0
12.5
14.0
13.0
10.0
9.0
12.0
11.0
12.0
11.0
13.0
12.0
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
ESRtyp
70 °C
10 kHz
mΩ
Untaped
pcs./MOQ
8.0 640
9.0 640
8.0 440
9.0 440
5.0 440
5.5 440
4.0 440
4.0 440
3.0 400
7.5 720
7.0 640
5.5 440
6.5 440
5.0 440
4.5 440
3.5 400
5.0 400
6.5 640
7.0 640
5.5 440
6.0 440
5.0 440
5.5 440
3.0 400
3.5 400
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 21
Datasheet pdf - http://www.DataSheet4U.co.kr/
5 Page B32774 ... B32778
MKP DC link high density series
Mounting guidelines
1 Soldering
1.1 Solderability of leads
The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.
Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.
Solder bath temperature
Soldering time
Immersion depth
Evaluation criteria:
Visual inspection
235 ±5 °C
2.0 ±0.5 s
2.0 +0/0.5 mm from capacitor body or seating plane
Wetting of wire surface by new solder ≥90%, free-flowing solder
1.2 Resistance to soldering heat
Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A.
www.DataSheet.net/
Conditions:
Series
Solder bath temperature Soldering time
MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C
coated
uncoated (lead spacing > 10 mm)
10 ±1 s
MFP
MKP (lead spacing > 7.5 mm)
MKT boxed (case 2.5 × 6.5 × 7.2 mm)
5 ±1 s
MKP (lead spacing ≤ 7.5 mm)
MKT uncoated (lead spacing ≤ 10 mm)
insulated (B32559)
<4s
recommended soldering
profile for MKT uncoated
(lead spacing ≤ 10 mm) and
insulated (B32559)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 21
Datasheet pdf - http://www.DataSheet4U.co.kr/
11 Page |
Páginas | Total 21 Páginas | |
PDF Descargar | [ Datasheet B32776E.PDF ] |
Número de pieza | Descripción | Fabricantes |
B32776E | Metallized Polypropylene Film Capacitors | EPCOS |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |