|
|
PDF G170EG01-V0 Data sheet ( Hoja de datos )
| Número de pieza | G170EG01-V0 | |
| Descripción | LCD Module | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de G170EG01-V0 (archivo pdf) en la parte inferior de esta página. Total 27 Páginas | ||
|
No Preview Available !
www.DataSheet4U.net
Avnet Embedded.
Support Around The Board™
Avnet Embedded
Specification.
Datasheet
AUO G170EG01-V0
www.avnet-embedded.eu
1 page  
www.DataSheet4U.net
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V0
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the CCFL reflector edge. Instead, press at the far
ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version1.0
4/25
5 Page 
www.DataSheet4U.net
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V0
3. Functional Block Diagram
The following diagram shows the functional block of the 17.0 inches Color TFT-LCD Module:
LVDS
+ 5V
AU ASIC
LVDS
Receiver
Timing
Controller
RSDS
DC/DC
Converter
Gamma
Correction
G1
TFT-LCD
1280*(3)*1024
Pixels
G1024
D1
D3840
4 CCFL
DC POWER
Inverter
PCBA Connector:
JAE FI-XB30SSL-HF15
Or Compatible
CCFL Connector:
YENONHO 35001HS-02L
Or Compatible
document version1.0
10/25
11 Page | ||
| Páginas | Total 27 Páginas | |
| PDF Descargar | [ Datasheet G170EG01-V0.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| G170EG01-V0 | LCD Module | AUO |
| G170EG01-V1 | LCD Module | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |