|
|
Número de pieza | G121SN01-V0 | |
Descripción | LCD Module | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de G121SN01-V0 (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
No Preview Available ! www.DataSheet4U.net
Gleichmann & Co. Electronics GmbH
Product Marketing Displays & Systems
Industriestr. 16, D- 76297 Stutensee
Tel :07249-910-0, Fax: 07249-910-559
http://www.msc-ge.com
Spec. No.: MDGD012-SN01-1
Version:
1
Total pages:
28
Date:
2005 - May - 09
AU OPTRONICS CORPORATION
Product Functional Specifications
12.1” SVGA Color TFT-LCD Module
Model Name: G0121SN01 V.0
Approved by
Martin Sun
Prepared by
Cynthia Lin
GD- MDBU Marketing Division / AU Optronics Croporation
Customer
Checked & Approved by
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.0 ver.1
1/28
1 page www.DataSheet4U.net
1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnection from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a module has to be put back into the packing container slot after once it
was taken out from the container, do not press the center of the CCFL Reflector
edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise
the TFT module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the interface Connector of the TFT module.
11) After installation of the TFT module into an enclosure, do not twist nor bend the
TFT module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from
outside. Otherwise the TFT module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD
module should be supplied by power complied with requirements of Limited Power
Source, or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit. Do not connect the CFL in Hazardous Voltage Circuit.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.0 ver.1
5/28
5 Page www.DataSheet4U.net
Note 3: Definition of response time
The output signals of BM-7 or equivalent are measured when the input signals are changed
from “Black” to “White” (rising time) and from “White” to “Black” (falling time), respectively. The
response time interval between the 10% and 90% of amplitudes. Refer to figure as below.
"White"
100%
90%
"Black"
"White"
10%
0% TTfr
TrTf
Note 4: Definition of contrast ration
Contrast ratio is calculated with the following formula.
Brightness on the “White” state
Contrast ratio (CR)= Brightness on the “Black” state
Note 5: Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a
180° horizontal and 180° vertical range (off-normal viewing angles). The 180 ° viewing angle
range is broken down as follows; 90 ° (θ) horizontal left and right and 90 ° (Φ) vertical, high
(up) and low (down). The measurement direction is typically perpendicular to the display
surface with the screen rotated about its center to develop the desired measurement viewing
angle.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G121SN01 V.0 ver.1
11/28
11 Page |
Páginas | Total 28 Páginas | |
PDF Descargar | [ Datasheet G121SN01-V0.PDF ] |
Número de pieza | Descripción | Fabricantes |
G121SN01-V0 | LCD Module | AUO |
G121SN01-V1 | LCD Module | AUO |
G121SN01-V2 | LCD Module | AUO |
G121SN01-V3 | LCD Module | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |