DataSheet.es    

PDF G104SN03-V0 Datasheet ( Hoja de datos )

Número de pieza G104SN03-V0
Descripción LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo

Total 27 Páginas
		
G104SN03-V0 Hoja de datos, Descripción, Manual
www.DataSheet4U.net
Specification for
G104SN03 V0
06 / Feb / 2004
Note: This Specification is subject to change without notice.
Data Modul AG - Landsberger Str. 322 - 80687 München - Tel. 089-56017-0 - Fax 089-56017-119 – www.data-modul.de

1 page

G104SN03-V0 pdf
www.DataSheet4U.net
1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnection from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open nor modify the module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far
ends of the CFL Reflector edge softly. Otherwise the TFT module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
interface Connector of the TFT module.
11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module should be
supplied by power complied with requirements of Limited Power Source, or be applied exemption.
14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not
connect the CFL in Hazardous Voltage Circuit.
(C) Copyright AU Optronics, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G104SN03 V.0
5/26

5 Page

G104SN03-V0 arduino
www.DataSheet4U.net
Note 6: Definition of viewing angle:
θ
θ
Note 7: Definition of the 13 points (from A to M) on panel, refer to figure as below
Note 8: Definition of brightness: the luminance of center points (G).
Note 9: Driving conditions for CCFL : IL=4.5 mA, 60KHz Frequency
Note 10: Definition of white uniformity:
Maximum Luminance of thirteen points (brightness)
δw = Minimum Luminance of thirteen points (brightness)
(C) Copyright AU Optronics, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G104SN03 V.0
11/26

11 Page


PáginasTotal 27 Páginas
PDF Descargar[ G104SN03-V0.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
G104SN03-V0LCD ModuleAUO
AUO
G104SN03-V1LCD ModuleAUO
AUO
G104SN03-V2LCD ModuleAUO
AUO
G104SN03-V5LCD ModuleAUO
AUO

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2018   |  Privacy Policy  |  Contacto  |  Buscar