PDF G104SN02-V1 Datasheet ( Hoja de datos )

Número de pieza G104SN02-V1
Descripción LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo

Total 27 Páginas
G104SN02-V1 Hoja de datos, Descripción, Manual
Produktspezifikation für AUO G104SN02 V1
Im Programm von
Dieses Dokument unterliegt nicht dem Änderungsdienst. Der Stand
entspricht der Drucklegung. Bitte informieren Sie sich vor Verwendung
ob die technischen Daten noch dem aktuellen Stand entsprechen. Trotz
sorgfältiger Kontrolle können wir leider keine Haftung für Druckfehler
oder Irrtümer übernehmen.

1 page

G104SN02-V1 pdf
G104SN02 V1
1. Operating Precautions
1) Since front polarizer is easily damaged, please be cautious and not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open nor modify the module assembly.
8) Do not press the reflector sheet at the back of the module to any direction.
9) In case if a module has to be put back into the packing container slot after it was taken
out from the container, do not press the center of the CCFL Reflector edge. Instead,
press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may
be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
15) Severe temperature condition may result in different luminance, response time and lamp
ignition voltage.
16) Continuous operating TFT-LCD display under low temperature environment may accelerate
lamp exhaustion and reduce luminance dramatically.
17) The data on this specification sheet is applicable when LCD module is placed in landscape
18) Continuous displaying fixed pattern may induce image sticking. It s recommended to use
screen saver or shuffle content periodically if fixed pattern is displayed on the screen.
G104SN02 V1 rev. 0.0
Page 4/26

5 Page

G104SN02-V1 arduino
4. Absolute Maximum Ratings
4.1 Absolute Ratings of TFT LCD Module
Logic/LCD Drive
4.2 Absolute Ratings of Environment
Operating Temperature
Operation Humidity
Storage Temperature
Storage Humidity
Note: Maximum Wet-Bulb should be 39and no condensation.
G104SN02 V1
G104SN02 V1 rev. 0.0
Page 10/26

11 Page

PáginasTotal 27 Páginas
PDF Descargar[ G104SN02-V1.PDF ]

Enlace url

Hoja de datos destacado

Número de piezaDescripciónFabricantes
G104SN02-V0LCD ModuleAUO
G104SN02-V1LCD ModuleAUO
G104SN02-V2LCD ModuleAUO

Número de piezaDescripciónFabricantes

High Voltage 3 phase Motor Driver IC.


12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.    |   2018   |  Privacy Policy  |  Contacto  |  Buscar