|
|
Número de pieza | B121EW07_V1 | |
Descripción | WXGA Color TFT-LCD | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de B121EW07_V1 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! Product Specification
B121EW07 V1
AU OPTRONICS CORPORATION
Product Specification
12.1” WXGA Color TFT-LCD Module
Model Name: B121EW07 V1
Approved by
Prepared by
www.DataSheet.co.kr
NBBU Marketing Division / AU Optronics corporation
Customer
Checked & Approved by
Document version 0.3
1/34
Datasheet pdf - http://www.DataSheet4U.net/
1 page Product Specification
1. Handling Precautions
B121EW07 V1
1.1. Since front polarizer is easily damaged, pay attention not to scratch it.
1.2. Be sure to turn off power supply when inserting or disconnecting from input connector.
1.3. Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
1.4. When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
1.5. Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
1.6. Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
1.7. Do not open nor modify the Module Assembly.
1.8. Do not press the reflector sheet at the back of the module to any directions.
1.9. In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the LED Reflector edge. Instead, press at the far
ends of the LED Reflector edge softly. Otherwise the TFT Module may be damaged.
1.10. At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
1.11. After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not
twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken
into consideration that no bending/twisting forces are applied to the TFT Module from outside.
Otherwise the TFT Module may be damaged.
www.DataSheet.co.kr
1.12. Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption,
1.13. Disconnecting power supply before handling LCD modules, it can prevent electric shock, DO
NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT module that a
LED light bar build in as a light source of back light unit. High voltage is supplied to these parts
when power turn on.
Document version 0.3
5/34
Datasheet pdf - http://www.DataSheet4U.net/
5 Page Product Specification
B121EW07 V1
3. Functional Block Diagram
The following diagram shows the functional block of the 12.1 inches wide Color TFT/LCD
Module:
www.DataSheet.co.kr
Document version 0.3
11/34
Datasheet pdf - http://www.DataSheet4U.net/
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet B121EW07_V1.PDF ] |
Número de pieza | Descripción | Fabricantes |
B121EW07-V0 | WXGA Color TFT-LCD | AUO |
B121EW07-V1 | WXGA Color TFT-LCD | AUO |
B121EW07_V0 | WXGA Color TFT-LCD | AUO |
B121EW07_V1 | WXGA Color TFT-LCD | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |