|
|
PDF SDM109N-R25MF Data sheet ( Hoja de datos )
| Número de pieza | SDM109N-R25MF | |
| Descripción | MOLDING TYPE DIP INDUCTORS | |
| Fabricantes | Superworld | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SDM109N-R25MF (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
www.DataSheet.co.kr
MOLDING TYPE DIP INDUCTORS
SDM109N SERIES
1. PART NO. EXPRESSION :
SDM109N-R25MF
(a) (b)
(c) (d)(e)
(a) Series code
(b) Dimension code
(c) Inductance code : R25 = 0.25uH
(d) Tolerance code : M = ±20%
(e) F : Lead Free
2. CONFIGURATION & DIMENSIONS :
A
R50
ØW
F
O
11.5
PCB Pattern
Unit:m/m
ABCDEF
10.5 Max. 10.5 Max. 10.0 Max. 3.4±0.5 5.3±1.0 5.3±1.0
W L M ØN O P
1.3±0.1 7.5±0.5 7.5 Typ. 1.6 Typ. 5.3±0.15 5.3±0.15
3. SCHEMATIC :
4. MATERIALS :
(a) Core : M-Iron Core
(b) Wire : Enamelled Copper Wire
(c) Adhesive : Epoxy
5. FEATURES :
a) Shielded construction
b) Frequency up to 1MHz
NOTE : Specifications subject to change without notice. Please check our website for latest information.
18.04.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
Datasheet pdf - http://www.DataSheet4U.net/
1 page  
www.DataSheet.co.kr
MOLDING TYPE DIP INDUCTORS
10. SOLDERIND AND MOUNTING :
10-1. Recommended PC Board Pattern
Ø1.6 Typ.
SDM109N SERIES
5.3±0.15
11.5
10-2. Soldering
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused
by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all
wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot
air soldering tools.
10-2.1 Solder Re-flow :
Recommended temperature profiles for re-flow soldering in Figure 1.
10-2.2 Soldering Iron (Figure 2) :
Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that
a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150°C.
b) 280°C tip temperature (max)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (max)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 3 secs.
Preheating Soldering
250~260
230
10s max.
180
150
Natural
cooling
60~120s
30~60s
Figure 1. Re-flow Soldering
Preheating Soldering Natural
cooling
350
300
150
Over 1min.
Gradual
Cooling
Within 3secs.
Figure 2. Iron Soldering
NOTE : Specifications subject to change without notice. Please check our website for latest information.
18.04.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5
Datasheet pdf - http://www.DataSheet4U.net/
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet SDM109N-R25MF.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SDM109N-R25MF | MOLDING TYPE DIP INDUCTORS | Superworld |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |