DataSheet.es    


PDF W25X32BV Data sheet ( Hoja de datos )

Número de pieza W25X32BV
Descripción 32M-BIT SERIAL FLASH MEMORY
Fabricantes Winbond 
Logotipo Winbond Logotipo



Hay una vista previa y un enlace de descarga de W25X32BV (archivo pdf) en la parte inferior de esta página.


Total 45 Páginas

No Preview Available ! W25X32BV Hoja de datos, Descripción, Manual

www.DataSheet.co.kr
W25X32BV
32M-BIT
SERIAL FLASH MEMORY WITH
4KB SECTORS AND DUAL OUTPUT SPI
The W25Q32BV is recommended for all new 32Mb designs. The W25X32BV is
available for existing designs that require "25X" device ID for firmware
compatibility.
Publication Release Date: October 7, 2009
- 1- Preliminary -- Revision C
Datasheet pdf - http://www.DataSheet4U.net/

1 page




W25X32BV pdf
www.DataSheet.co.kr
3. PIN CONFIGURATION SOIC 208-MIL
W25X32BV
Figure 1a. W25X32BV Pin Assignments, 8-pin SOIC 208-mil (Package Code SS)
4. PAD CONFIGURATION WSON 6X5-MM / WSON 8X6-MM
Figure 1b. W25X32BV Pad Assignments, 8-pad WSON 6X5-mm (Package Code ZP) and 8x6-mm (Package Code ZE)
5. PIN DESCRIPTION SOIC 208-MIL, WSON 6X5-MM, WSON 8X6-MM
PIN NO.
1
2
3
4
5
6
7
8
PIN NAME
/CS
DO
/WP
GND
DIO
CLK
/HOLD
VCC
I/O FUNCTION
I Chip Select Input
O Data Output
I Write Protect Input
Ground
I/O Data Input / Output
I Serial Clock Input
I Hold Input
Power Supply
Publication Release Date: October 7, 2009
- 5 - Preliminary -- Revision C
Datasheet pdf - http://www.DataSheet4U.net/

5 Page





W25X32BV arduino
www.DataSheet.co.kr
W25X32BV
10. CONTROL AND STATUS REGISTERS
The Read Status Register instruction can be used to provide status on the availability of the Flash
memory array, if the device is write enabled or disabled, and the state of write protection. The Write
Status Register instruction can be used to configure the device write protection features. See Figure 3.
10.1 STATUS REGISTER
10.1.1 BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing
a Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction. During
this time the device will ignore further instructions except for the Read Status Register instruction (see
tW, tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status register
instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for
further instructions.
10.1.2 Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing
a Write Enable Instruction. The WEL status bit is cleared to a 0 when the device is write disabled. A
write disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Sector Erase, Block Erase, Chip Erase and Write Status Register.
10.1.3 Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, and BP0) are non-volatile read/write bits in the status register (S4,
S3, and S2) that provide Write Protection control and status. Block Protect bits can be set using the
Write Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory
array can be protected from Program and Erase instructions (see Status Register Memory Protection
table). The factory default setting for the Block Protection Bits is 0, none of the array protected. The
Block Protect bits can not be written to if the Status Register Protect (SRP) bit is set to 1 and the Write
Protect (/WP) pin is low.
10.1.4 Top/Bottom Block Protect (TB)
The Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the Top
(TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table.
The TB bit is non-volatile and the factory default setting is TB=0. The TB bit can be set with the Write
Status Register Instruction provided that the Write Enable instruction has been issued. The TB bit can
not be written to if the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP) pin is
low.
10.1.5 Reserved Bits
Status register bit location S6 is reserved for future use. Current devices will read 0 for this bit
location. It is recommended to mask out the reserved bit when testing the Status Register. Doing this
will ensure compatibility with future devices.
- 11 -
Publication Release Date: October 7, 2009
Preliminary -- Revision C
Datasheet pdf - http://www.DataSheet4U.net/

11 Page







PáginasTotal 45 Páginas
PDF Descargar[ Datasheet W25X32BV.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
W25X32BV32M-BIT SERIAL FLASH MEMORYWinbond
Winbond

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar