|
|
Número de pieza | W25X32A | |
Descripción | 32M-BIT SERIAL FLASH MEMORY | |
Fabricantes | Winbond | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de W25X32A (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! www.DataSheet.co.kr
W25X32A
32M-BIT
SERIAL FLASH MEMORY WITH
4KB SECTORS AND DUAL OUTPUT SPI
-1-
Publication Release Date: August 7, 2009
Preliminary - Revision B
Datasheet pdf - http://www.DataSheet4U.net/
1 page www.DataSheet.co.kr
3 PIN CONFIGURATION SOIC 208-MIL
W25X32A
Figure 1a. W25X32A Pin Assignments, 8-pin SOIC 208-mil (Package Code SS)
4 PAD CONFIGURATION WSON 6X5-MM & 8X6-MM
Figure 1b. W25X32A Pad Assignments, 8-pad WSON 6x5-mm (Package Code ZP) & 8x6-mm (Package Code ZE)
5
PIN DESCRIPTION SOIC 208-MIL, WSON 6X5-MM, WSON 8X6-MM
PIN NO.
1
2
3
4
5
6
7
8
PIN NAME
/CS
DO
/WP
GND
DIO
CLK
/HOLD
VCC
I/O FUNCTION
I Chip Select Input
O Data Output
I Write Protect Input
Ground
I/O Data Input / Output
I Serial Clock Input
I Hold Input
Power Supply
-5-
Publication Release Date: August 7, 2009
Preliminary - Revision B
Datasheet pdf - http://www.DataSheet
5 Page www.DataSheet.co.kr
W25X32A
10 CONTROL AND STATUS REGISTERS
The Read Status Register instruction can be used to provide status on the availability of the Flash
memory array, if the device is write enabled or disabled, and the state of write protection. The Write
Status Register instruction can be used to configure the devices write protection features. See Figure 3.
10.1 STATUS REGISTER
10.1.1 BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction. During this
time the device will ignore further instructions except for the Read Status Register instruction (see tW, tPP,
tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status register instruction has
completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions.
10.1.2 Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to a 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Sector Erase, Block Erase, Chip Erase and Write Status Register.
10.1.3 Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, and BP0) are non-volatile read/write bits in the status register (S4, S3,
and S2) that provide Write Protection control and status. Block Protect bits can be set using the Write
Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can
be protected from Program and Erase instructions (see Status Register Memory Protection table). The
factory default setting for the Block Protection Bits is 0, none of the array protected. The Block Protect bits
can not be written to if the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP) pin is
low.
10.1.4 Top/Bottom Block Protect (TB)
The Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the Top (TB=0) or
the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The TB bit is
non-volatile and the factory default setting is TB=0. The TB bit can be set with the Write Status Register
Instruction provided that the Write Enable instruction has been issued. The TB bit can not be written to if
the Status Register Protect (SRP) bit is set to 1 and the Write Protect (/WP) pin is low.
10.1.5 Reserved Bits
Status register bit location S6 is reserved for future use. Current devices will read 0 for this bit location. It
is recommended to mask out the reserved bit when testing the Status Register. Doing this will ensure
compatibility with future devices.
- 11 -
Publication Release Date: August 7, 2009
Preliminary - Revision B
Datasheet pdf - http://www.DataSheet4U.net/
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet W25X32A.PDF ] |
Número de pieza | Descripción | Fabricantes |
W25X32 | (W25X16 - W25X64) Serial Flash Memory | Winbond Electronics |
W25X32A | 32M-BIT SERIAL FLASH MEMORY | Winbond |
W25X32BV | 32M-BIT SERIAL FLASH MEMORY | Winbond |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |