DataSheet.es    


PDF 42LG6000 Data sheet ( Hoja de datos )

Número de pieza 42LG6000
Descripción (42LG6000 / 42LG6100) LCD TV Service Manual
Fabricantes LG 
Logotipo LG Logotipo



Hay una vista previa y un enlace de descarga de 42LG6000 (archivo pdf) en la parte inferior de esta página.


Total 27 Páginas

No Preview Available ! 42LG6000 Hoja de datos, Descripción, Manual

www.DataSheet.co.kr
Internal Use Only
website:http://biz.LGservice.com
LCD TV
SERVICE MANUAL
CHASSIS : LD89F
MODEL : 42LG6000 42LG6000-ZA
42LG6100 42LG6100-ZB
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Datasheet pdf - http://www.DataSheet4U.net/

1 page




42LG6000 pdf
www.DataSheet.co.kr
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as
possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
Copyright C 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
-5-
LGE Internal Use Only
Datasheet pdf - http://www.DataSheet4U.net/

5 Page





42LG6000 arduino
www.DataSheet.co.kr
9. Mechanical specification
9-1. 37LG6000
No, Item
1 Product Dimenson
Before Packing
After Packing
2 Product Weight
Only SET
With Box
3 Container Loading Quantity Individual or
Palletizing
4 Stand Assy
5 Appearance
Type
Size(W x D x H)
Tilt Degree
Tilt force
Swivel Degree
Swivel Force
9-2. 42LG6000
No, Item
1 Product Dimenson
Before Packing
After Packing
2 Product Weight
Only SET
With Box
3 Container Loading Quantity Individual or
Palletizing
4 Stand Assy
5 Appearance
Type
Size(W x D x H)
Tilt Degree
Tilt force
Swivel Degree
Swivel Force
Content
Width(W) Length(D) Height(H)
Unit
929 374.7 707
mm
1015
277
782
mm
21.7
Kg
26.2
Kg
20ft 40ft
Indi Wooden Indi Woonden
291 291 88
Attachde(detachable)
460
375.4
234.1
mm
-
-
Swivel(+/- 20degree)
1.0 ~ 2.0kgf
Refer to Standard of LG(56)G4-9002
Remark
Content
Width(W) Length(D) Height(H)
Unit
1037.6
378
795
mm
1330
257
844
mm
22.7
Kg
27.2
Kg
40ft 40ft(H-CUBIC)
Indi Wooden Indi Woonden
162 243
Attachde(detachable)
520.1
379.5
265.1
mm
-
-
Swivel(+/- 20degree)
0.8 ~ 1.5kgf
Refer to Standard of LG(56)G4-9002
Remark
Copyright C 2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes
- 11 -
LGE Internal Use Only
Datasheet pdf - http://www.DataSheet4U.net/

11 Page







PáginasTotal 27 Páginas
PDF Descargar[ Datasheet 42LG6000.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
42LG6000(42LG6000 / 42LG6100) LCD TV Service ManualLG
LG

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar