|
|
PDF LM057QC1T08 Data sheet ( Hoja de datos )
| Número de pieza | LM057QC1T08 | |
| Descripción | Display Module | |
| Fabricantes | Sharp | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LM057QC1T08 (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
|
No Preview Available !
1 page  
www.DataSheet.co.kr
SPEC No.
MODEL No.
LCY-W06802
LM057QC1T08
PAGE
3
13) Procedure insert mating connector
When the mating connector is inserted, it should be parallel to the used connector of LCD module and it
should be inserted horizontally.
When the mating connector is attempted to be fixed to LCD connector, it should be inserted properly in order
not to create a gap.
Please insert the connector as both edge is placed to the connect position of LCD connector.
14) The module should be driven according to the specified ratings to avoid permanent damage.
DC voltage drive leads to rapid deterioration of LC, so ensure that the drive is alternating waveform by
continuous application of the signal M. Especially the power ON/OFF sequence shown on Page 16 should be
kept to avoid latch-up of drive LSIs and application of DC voltage to LCD panel.
15) It is a characteristic of LCD to maintain the displaying pattern when the pattern is a applied for long time.
(Image retention)
To prevent image retention, please do not apply the fixed pattern for along time by pre-installing such
programs at your side.
16) This phenomena (image retention) is not deterioration of LCD. It if happens, you can remove it by
applying different patterns.
17) CCFT backlight should be kept OFF during VDD is “L” level.
Datasheet pdf - http://www.DataSheet4U.net/
5 Page 
www.DataSheet.co.kr
SPEC No.
MODEL No.
LCY-W06802
LM057QC1T08
PAGE
9
5-2 Interface signals
○ LCD
No. Symbols
1 YD
2 LP
3 XCK
4 DISP
5 VDD
6 VSS
7 VEE
8 D7
9 D6
10 D5
11 D4
12 D3
13 D2
14 D1
15 D0
Table 6 CN1 (LCD)
Description
scan start-up signal
input latch signal
data input clock signal
display control signal
power supply for logic
ground potential
power supply for LCD
Note
“H”
“H” → ”L”
“H” → ”L”
“H” display on , “L” display off
-
-
-
display data signal
“H” (ON) , ”L”(OFF)
○ Inverter
Table 7 CN2 (CCFT)
No. Symbols
Description
1 VL1(HV)
High voltage line(from Inverter)
2 NC
-
3 VL2(GND)
ground line(from Inverter)
Used connector
CN1 : 53216-1571
(MOLEX)
CN2 : BHR-03VS-1
(JST)
Note
for back light
Correspondable connector
CN1 : 51021-1571
CN2 : SM02-(8.0)B-BHS-1
(MOLEX)
(JST)
Except above connector shall be out of guaranty.
Datasheet pdf - http://www.DataSheet4U.net/
11 Page | ||
| Páginas | Total 24 Páginas | |
| PDF Descargar | [ Datasheet LM057QC1T08.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LM057QC1T01 | NEGATIVE MATRIX TYPE COLOR LCD MODULE |  Sharp Electrionic Components |
| LM057QC1T08 | Display Module | Sharp |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |