DataSheet.es    


PDF LB11660RV Data sheet ( Hoja de datos )

Número de pieza LB11660RV
Descripción Single-Phase Full-Wave Driver
Fabricantes Sanyo Semicon Device 
Logotipo Sanyo Semicon Device Logotipo



Hay una vista previa y un enlace de descarga de LB11660RV (archivo pdf) en la parte inferior de esta página.


Total 9 Páginas

No Preview Available ! LB11660RV Hoja de datos, Descripción, Manual

www.DataSheet.co.kr
Ordering number : ENA0082
LB11660RV
Monolithic Digital IC
Single-Phase Full-Wave Driver
For Fan Motor
Overview
The LB11660RV is a single-phase bipolar half pre-driver that can achieve high-efficient direct PWM drive with ease. It
is ideal for driving small-sized cooling fans used in servers. The LB11660RV is provided with the RD (lock detection)
output pin and the LB11660FV the FG (rotational speed detection) output pin, respectively.
Features
Single-phase full-wave drive (15V-1.5A output transistor built in) upper output Tr incorporated half pre-driver.
Variable speed control by an external signal.
Separately-excited upper TR direct PWM control method, enabling silent, low-vibration variable speed control.
Lowest speed setting possible.
Current limiter circuit (the circuit actuated at IO = 1A when Rf = 0.5, Rf determines the limiter value.).
Kickback absorption circuit built in.
Soft switching circuit achieves low power consumption, low loss, and low noise driving at a time of phase change.
HB built in.
Lock protection and automatic reset functions incorporated (including a circuit that changes the ON/OFF ratio according
to the power supply voltage).
RD (lock detection) output.
Thermal protection circuit incorporated (design guaranteed).
Any and all SANYO Semiconductor products described or contained herein do not have specifications
that can handle applications that require extremely high levels of reliability, such as life-support systems,
aircraft's control systems, or other applications whose failure can be reasonably expected to result in
serious physical and/or material damage. Consult with your SANYO Semiconductor representative
nearest you before using any SANYO Semiconductor products described or contained herein in such
applications.
SANYO Semiconductor assumes no responsibility for equipment failures that result from using products
at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor
products described or contained herein.
D2706 TI IM B8-9145 No.A0082-1/9
Datasheet pdf - http://www.DataSheet4U.net/

1 page




LB11660RV pdf
www.DataSheet.co.kr
LB11660RV
*1 <Power supply - GND wiring>
GRD of the IC is connected to the control circuit power supply system and GRD of the external N-channel is
connected to the motor power supply system. Groundings must be installed separately and all external control
components must be connected to the GND line of the IC.
*2 <Power stabilization capacitor for regeneration>
For the CM capacitor, that is a power stabilization capacitor for PWM drive and for absorption of kick-back, a
capacitance of 4.7µF/25V or higher must be used. The CM capacitor must be connected without fail to prevent the
IC from being damaged when power is tuned on or off.
*3 <Speed control>
1) Control voltage
The PWM duty ratio is determined by comparing the VTH pin voltage and the PWM oscillation waveforms.
When the VTH pin voltage drops, the 'ON' duty ratio increases, and when it drops to or below the PWM output L
level voltage, the duty ratio is 100%.
2) Thermistor
In thermistor applications, the 6VREG voltage is usually divided by a resistor, and the voltage thus generated is
supplied to the VTH pin.
The PWM duty ratio is varied by the changes in the VTH pin voltage which result from changes in temperature.
*4 < Setting the current limiter >
The current limiter is actuated when the voltage of the current-sensing resistors between VCC and VM increases to
0.5V or more.
Since the current of a current limiter circuit is limited by the current determined by IO = VRf/Rf (where VRf = 0.5V
typ, Rf: current-sensing resistance), the current limiter is actuated at IO = 1A when Rf = 0.5. The Rf resistor must
be connected without fail, and its constant must be within the recommended operating range for current limiters.
*5 <Hall input>
Wiring need to be short to prevent carrying of the noise. The Hall input circuit is a comparator having a hysteresis of
20mV. It is recommended that the Hall input level be more than three times (60mVp-p) this hysteresis.
*6 < PWM oscillation frequency setting capacitor >
The oscillation frequency is 23kHz when CP = 200pF and 46kHz when CP = 100pF, and this serves as the PWM
fundamental frequency.
For the most part, the PWM frequency can be obtained from the following formula:
f [kHz] (4.6×106) ÷C [pF]
*7 <RD output>
This is the open collector type output, which outputs ''L'' during rotation. It is set to 'OFF' when a lock is detected.
This output is left open when not in use.
*8 <HB pin>
This is a Hall element bias pin, that is, the 1.25V constant-voltage output pin.
*9 <RMI pin>
Lowest speed setting pin for speed control.
The minimum output duty setting is made with R3 and R4. The R4 is left open to stop operation at a duty ratio
of 0%.
No.A0082-5/9
Datasheet pdf - http://www.DataSheet4U.net/

5 Page










PáginasTotal 9 Páginas
PDF Descargar[ Datasheet LB11660RV.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LB11660RVSingle-Phase Full-Wave DriverSanyo Semicon Device
Sanyo Semicon Device
LB11660RVHalf-pre Motor Driver Single-Phase Full-WaveON Semiconductor
ON Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar