DataSheet.es    


PDF G150XG03_V1 Data sheet ( Hoja de datos )

Número de pieza G150XG03_V1
Descripción LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo



Hay una vista previa y un enlace de descarga de G150XG03_V1 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! G150XG03_V1 Hoja de datos, Descripción, Manual

www.DataSheet4U.net
Product Specification
G150XG03 V.1
AU OPTRONICS CORPORATION
Product Specification
15.0XGA Color TFT-LCD Module
Model Name: G150XG03 V.1
Approved by
Peter ML Lee
Prepared by
Daniel Chi
GDBD Marketing Division / AU Optronics corporation
Customer
Checked & Approved by
G150XG03 V1 ver 0.1
1/30

1 page




G150XG03_V1 pdf
www.DataSheet4U.net
1.0 Handling Precautions
Product Specification
G150XG03 V.1
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open nor modify the Module Assembly.
8) Do not press or pat the panel surface by fingers,hand or tooling.
9) Do not press the reflector sheet at the back of the module to any directions.
10) In case if a module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL
reflector edge softly. Otherwise the TFT module may be damaged.
11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT module.
12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist
nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the
TFT module may be damaged.
G150XG03 V1 ver 0.1
5/30

5 Page





G150XG03_V1 arduino
www.DataSheet4U.net
Product Specification
G150XG03 V.1
3.0 Functional Block Diagram
The following diagram shows the functional block of the 15.0 inches wide Color TFT/LCD Module:
LVDS
+ 3.3V
AU ASIC
LVDS
Receiver
Timing
Controller
RSDS
Transmitter
DC/DC
Converter
Gamma
Correction
G1
TFT-LCD
1024(3)*768
Pixels
G768
Source Driver IC
X-Driver IC
D1 D3072
2 CCFL
DC POWER
Inverter
CWY20G A0G16 / MSB240420
Mating Type: HRS DF14-20S-1.25C
JST-BHR-03VS-1
SM02(8.0)B-BHS-1-TB
G150XG03 V1 ver 0.1
11/30

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet G150XG03_V1.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
G150XG03-V0LCD ModuleAUO
AUO
G150XG03-V1LCD ModuleAUO
AUO
G150XG03-V2LCD ModuleAUO
AUO
G150XG03-V3LCD ModuleAUO
AUO

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar