|
|
PDF B121EW09-V3 Data sheet ( Hoja de datos )
| Número de pieza | B121EW09-V3 | |
| Descripción | LCD Module | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de B121EW09-V3 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Product Specification
AU OPTRONICS CORPORATION
( ) Preliminary Specifications
(V ) Final Specifications
Module
Model Name
Note ( )
WXGA Color TFT-LCD with LED Backlight design
B121EW09 V3 (H/W:1A)
LED Backlight with driving circuit design
Customer
Date
Checked &
Approved by
Date
Note: This Specification is subject to change
without notice.
document version 1.2
www.DataSheet4U.net
Approved by
Howard Lee
Date
2010/01/15
Prepared by
Date
Donna Yang
2010/01/15
NBBU Marketing Division /
AU Optronics corporation
1 of 35
1 page  
Product Specification
AU OPTRONICS CORPORATION
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11)After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12)Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13)Disconnecting power supply before handling LCD modules, it can prevent electric shock, DO
NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT module
that a LED light bar build in as a light source of back light unit. It can prevent electrostic
breakdown.
document version 1.2
5 of 35
5 Page 
Product Specification
AU OPTRONICS CORPORATION
Note 8. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180°horizontal an d 180°
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90 °( θ)
horizontal left and right and 90°( Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
document version 1.2
11 of 35
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet B121EW09-V3.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| B121EW09-V0 | LCD Module | AUO |
| B121EW09-V1 | LCD Module | AUO |
| B121EW09-V2 | LCD Module | AUO |
| B121EW09-V3 | LCD Module | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |