DataSheet.es    


PDF B140XW02-V2 Data sheet ( Hoja de datos )

Número de pieza B140XW02-V2
Descripción LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo



Hay una vista previa y un enlace de descarga de B140XW02-V2 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! B140XW02-V2 Hoja de datos, Descripción, Manual

This Datasheet has been downloaded from:
DisplayAlliance.com
Please call +1 (978) 465-6190 or email [email protected] for a quote.
ISO 9001 : 2008
www.DataSheet4U.net

1 page




B140XW02-V2 pdf
Product Specification
AU OPTRONICS CORPORATION
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the Interface Connector of the TFT Module.
11)After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13) Disconnecting power supply before handling LCD modules, it can prevent electric shock,
DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT
module that a LED light bar build in as a light source of back light unit. It can prevent
electronic breakdown.
B140XW02 V2 Document Version : 0.3
4 of 29

5 Page





B140XW02-V2 arduino
Product Specification
AU OPTRONICS CORPORATION
Note 9. Definition of viewing angle
Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° ()
horizontal left and right and 90° () vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
B140XW02 V2 Document Version : 0.3
10 of 29

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet B140XW02-V2.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
B140XW02-V0LCD ModuleAUO
AUO
B140XW02-V1LCD ModuleAUO
AUO
B140XW02-V2LCD ModuleAUO
AUO

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar