|
|
Número de pieza | K10P144M100SF2 | |
Descripción | K10 Sub-Family | |
Fabricantes | Freescale Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de K10P144M100SF2 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! Freescale Semiconductor
Data Sheet: Product Preview
Document Number: K10P144M100SF2
Rev. 4, 3/2011
K10 Sub-Family Data Sheet
Supports the following:
MK10X128VLQ100,
MK10X128VMD100,
MK10X256VLQ100,
MK10X256VMD100,
MK10N512VLQ100,
MK10N512VMD100
Features
• Operating Characteristics
– Voltage range: 1.71 to 3.6 V
– Flash write voltage range: 1.71 to 3.6 V
– Temperature range (ambient): -40 to 105°C
• Performance
– Up to 100 MHz ARM Cortex-M4 core with DSP
instructions delivering 1.25 Dhrystone MIPS per
MHz
• Memories and memory interfaces
– Up to 512 KB program flash memory on non-
FlexMemory devices
– Up to 256 KB program flash memory on
FlexMemory devices
– Up to 256 KB FlexNVM on FlexMemory devices
– 4 KB FlexRAM on FlexMemory devices
– Up to 128 KB RAM
– Serial programming interface (EzPort)
– FlexBus external bus interface
• Clocks
– 3 to 32 MHz crystal oscillator
– 32 kHz crystal oscillator
– Multi-purpose clock generator
• System peripherals
– 10 low-power modes to provide power optimization
based on application requirements
– Memory protection unit with multi-master
protection
www.Da–taS1h6e-ecth4aUn.ncoeml DMA controller, supporting up to 64
request sources
– External watchdog monitor
– Software watchdog
– Low-leakage wakeup unit
K10P144M100SF2
• Security and integrity modules
– Hardware CRC module to support fast cyclic
redundancy checks
– 128-bit unique identification (ID) number per chip
• Human-machine interface
– Low-power hardware touch sensor interface (TSI)
– General-purpose input/output
• Analog modules
– Two 16-bit SAR ADCs
– Programmable gain amplifier (up to x64) integrated
into each ADC
– Two 12-bit DACs
– Three analog comparators (CMP) containing a 6-bit
DAC and programmable reference input
– Voltage reference
• Timers
– Programmable delay block
– Eight-channel motor control/general purpose/PWM
timer
– Two 2-channel quadrature decoder/general purpose
timers
– Periodic interrupt timers
– 16-bit low-power timer
– Carrier modulator transmitter
– Real-time clock
• Communication interfaces
– Two Controller Area Network (CAN) modules
– Three SPI modules
– Two I2C modules
– Six UART modules
– Secure Digital host controller (SDHC)
– I2S module
This document contains information on a product under development. Freescale
reserves the right to change or discontinue this product without notice.
© 2010–2011 Freescale Semiconductor, Inc.
Preliminary
1 page Field
FFF
Description
Program flash memory size
T Temperature range (°C)
PP Package identifier
CCC
Maximum CPU frequency (MHz)
N Packaging type
Terminology and guidelines
Values
• 32 = 32 KB
• 64 = 64 KB
• 128 = 128 KB
• 256 = 256 KB
• 512 = 512 KB
• 1M0 = 1 MB
• V = –40 to 105
• C = –40 to 85
• FM = 32 QFN (5 mm x 5 mm)
• FT = 48 QFN (7 mm x 7 mm)
• LF = 48 LQFP (7 mm x 7 mm)
• EX = 64 QFN (9 mm x 9 mm)
• LH = 64 LQFP (10 mm x 10 mm)
• LK = 80 LQFP (12 mm x 12 mm)
• MB = 81 MAPBGA (8 mm x 8 mm)
• LL = 100 LQFP (14 mm x 14 mm)
• MC = 121 MAPBGA (8 mm x 8 mm)
• LQ = 144 LQFP (20 mm x 20 mm)
• MD = 144 MAPBGA (13 mm x 13 mm)
• MF = 196 MAPBGA (15 mm x 15 mm)
• MJ = 256 MAPBGA (17 mm x 17 mm)
• 50 = 50 MHz
• 72 = 72 MHz
• 100 = 100 MHz
• 120 = 120 MHz
• 150 = 150 MHz
• R = Tape and reel
• (Blank) = Trays
2.4 Example
This is an example part number:
MK10N512VMD100
3 Terminology and guidelines
3.1 Definition: Operating requirement
www.DataSheet4U.com
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
K10 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011.
Freescale Semiconductor, Inc.
Preliminary
5
5 Page Symbol
VAIO
ID
VDDA
VBAT
Description
Analog, RESET, EXTAL, and XTAL input voltage
Instantaneous maximum current single pin limit (applies to all
port pins)
Analog supply voltage
RTC battery supply voltage
Min.
–0.3
–25
VDD – 0.3
–0.3
Max.
VDD + 0.3
25
VDD + 0.3
3.8
General
Unit
V
mA
V
V
5 General
5.1 Nonswitching electrical specifications
5.1.1 Voltage and current operating requirements
Table 1. Voltage and current operating requirements
Symbol Description
VDD Supply voltage
VDDA
Analog supply voltage
VDD – VDDA VDD-to-VDDA differential voltage
VSS – VSSA VSS-to-VSSA differential voltage
VBAT
RTC battery supply voltage
VIH Input high voltage
• 2.7 V ≤ VDD ≤ 3.6 V
• 1.7 V ≤ VDD ≤ 2.7 V
Min.
1.71
1.71
–0.1
–0.1
1.71
Max.
3.6
3.6
0.1
0.1
3.6
0.7 × VDD
0.75 × VDD
—
—
Unit
V
V
V
V
V
V
V
VIL Input low voltage
• 2.7 V ≤ VDD ≤ 3.6 V
• 1.7 V ≤ VDD ≤ 2.7 V
— 0.35 × VDD V
— 0.3 × VDD V
VHYS
IIC
Input hysteresis
DC injection current — single pin
• VIN < VSS
0.06 × VDD
—
0 –0.2
V
mA
www.DataSheet4U.coDmC injection current — total MCU limit, includes sum
of all stressed pins
• VIN < VSS
0
–5 mA
VRAM
VRFVBAT
VDD voltage required to retain RAM
VBAT voltage required to retain the VBAT register file
1.2
TBD
—
—
V
V
K10 Sub-Family Data Sheet Data Sheet, Rev. 4, 3/2011.
Freescale Semiconductor, Inc.
Preliminary
Notes
1
1
11
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet K10P144M100SF2.PDF ] |
Número de pieza | Descripción | Fabricantes |
K10P144M100SF2 | K10 Sub-Family | Freescale Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |