DataSheet.es    


PDF MAU401 Data sheet ( Hoja de datos )

Número de pieza MAU401
Descripción Ultra High Isolation SIP SINGLE AND DUAL OUTPUT DC/DC Converters
Fabricantes Total Power International 
Logotipo Total Power International Logotipo



Hay una vista previa y un enlace de descarga de MAU401 (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! MAU401 Hoja de datos, Descripción, Manual

TOTAL POWER INT'L
MAU400 Series
1 Watt Ultra High In/Out Isolation SIP DC/DC Converters
Single and Dual Outputs
Key Features
y I/O Isolation 6000VDC
y Miniature Package
y Efficiency up to 75%
y SMT Technology
y Lost Cost
y MTBF > 2,000,000 Hours
MAU400 1W DC/DC's are specially designed to
provide ultra-high levels of isolation 6000VDC in a miniature
SIP package.
The series consists of 12 models with input voltages of 5V
and 12V, and offers standard output voltages of 5V, 12V, 15V
in both single and dual output configurations.
The MAU400 series is an excellent selection for a wide
variety of applications including distributed power systems,
mixed analog/digital subsystems, portable test equipments,
local power networks and battery backed systems.
$
Low Cost
6000
VDC
I/O Isolation
Low Profile
Block Diagram
Single Output
Dual Output
+Vin
www.DataFLSilCthereet4PUIBun.sivpcheoo-rlPtameurrll
-Vin
+Vo
+Vin
LC
Filter
-Vin
Bipolar
Push-Pull
Inverter
-Vo
+Vo
Com.
-Vo

1 page




MAU401 pdf
MAU400 Series
Test Configurations
Input Reflected-Ripple Current Test Setup
To Oscilloscope
+Vin +Out
+
Battery
+ Lin
Cin
Current
Probe
DC / DC
Converter
-Vin -Out
Load
Input reflected-ripple current is measured with a inductor
Lin (4.7uH) and Cin (220uF, ESR < 1.0[ at 100 KHz) to
simulate source impedance.
Capacitor Cin, offsets possible battery impedance.
Current ripple is measured at the input terminals of the
module, measurement bandwidth is 0-500 KHz.
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.33uF ceramic capacitor.
Scope measurement should be made by using a BNC
socket, measurement bandwidth is 0-20 MHz. Position the
load between 50 mm and 75 mm from the DC/DC Converter.
+Vin
+Out
Single Output
DC / DC
Converter
-Vin -Out
Copper Strip
Cout
Scope
Resistive
Load
In applications where power is supplied over long lines and
output loading is high, it may be necessary to use a capacitor
at the input to ensure startup.
Capacitor mounted close to the power module helps
ensure stability of the unit, it is recommended to use a good
quality low Equivalent Series Resistance (ESR < 1.0[ at 100
KHz) capacitor of a 2.2uF for the 5V input devices, a 1.0uF for
the 12V input devices.
Output Ripple Reduction
A good quality low ESR capacitor placed as close as
practicable across the load will give the best ripple and noise
performance.
To reduce output ripple, it is recommended to use 1.5uF
capacitors at the output.
+
DC Power
Source
-
+Vin
+Out
Single Output
DC / DC
Converter
-Vin -Out
Cout
Load
+
DC Power
Source
-
+Vin
+Out
Dual Output
DC / DC Com.
Converter
-Vin -Out
Cout
Load
+Vin
+Out
Dual Output
DC / DC Com.
Converter
-Vin -Out
Copper Strip
Cout
Cout
Scope
Resistive
Load
Scope
Design & Feature Considerations
Maximum Capacitive Load
The MAU400 series has limitation of maximum connected
capacitance at the output.
The power module may be operated in current limiting
mode during start-up, affecting the ramp-up and the startup
time.
For optimum performance we recommend 220uF
maximum capacitive load for dual outputs and 680uF
wwcwa.pDaactiatiSvheeleota4dUf.ocromsingle outputs.
The maximum capacitance can be found in the data.
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power module.
Thermal Considerations
Many conditions affect the thermal performance of the
power module, such as orientation, airflow over the module
and board spacing. To avoid exceeding the maximum
temperature rating of the components inside the power
module, the case temperature must be kept below 90°C.
The derating curves are determined from measurements
obtained in an experimental apparatus.
Position of air velocity
probe and thermocouple
15mm / 0.6in
50mm / 2in
Air Flow
DUT
+
DC Power
Source
-
+Vin
+ DC / DC
Converter
Cin
-Vin
+Out
-Out
Load

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet MAU401.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
MAU400Ultra High Isolation SIP SINGLE AND DUAL OUTPUT DC/DC ConvertersTotal Power International
Total Power International
MAU401Ultra High Isolation SIP SINGLE AND DUAL OUTPUT DC/DC ConvertersTotal Power International
Total Power International
MAU402Ultra High Isolation SIP SINGLE AND DUAL OUTPUT DC/DC ConvertersTotal Power International
Total Power International
MAU403Ultra High Isolation SIP SINGLE AND DUAL OUTPUT DC/DC ConvertersTotal Power International
Total Power International

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar