|
|
Número de pieza | S11059-01WT | |
Descripción | I2C interface-compatible color sensor | |
Fabricantes | Hamamatsu | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de S11059-01WT (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
No Preview Available ! Color sensor
S11059-01WT
I2C interface-compatible color sensor
The S11059-01WT is a color sensor that supports the I2C (inter-integrated circuit) interface. It is sensitive to red (O=615 nm),
green (O=530 nm), blue (O=460 nm), and infrared (O=855 nm) light, and outputs detected results as 16-bit digital data for each
color. The photodiode for each color is automatically switched sequentially to perform measurements. The sensitivity and integra-
tion time can be adjusted so that light measurements can be performed over a wide range.
Features
I2C interface compatible
Sequential measurements of red, green, blue, and infrared light
2-step sensitivity switching (sensitivity ratio 1 : 10)
Sensitivity adjustment by setting the integration time
Low voltage (2.5 V or 3.3 V) operation
Low current consumption: 75 NjA typ.
Small package (WL-CSP: wafer level-chip size package)
Internal infrared-cut ¿lter
Wide dynamic range (Low gain: 1 to 10 klx)
01Feature
I2C interface-compatible to allow direct connection to micro-controller
The sensor supports the I2C interface and so can exchange data
with the micro-controller using two signal lines jointly usable with
other devices. The digital output makes it easy to install into elec-
tronic devices such as cell phones and Àat-panel TVs whose micro-
controller is compatible with the I2C interface. The sensor supports
I2C Fast mode (400 kHz) and operates on 2.25 to 3.63 V.
Applications
LCD backlight adjustment for cell phones, notebook PC, etc.
Energy-saving sensor for large-size TV, etc.
Various types of light detection or color adjustment
02Feature
WL-CSP makes the device even smaller and highly reliable
The WL-CSP measures only 1.18 × 1.68 × 0.58 mm and lead-free
reÀow solder (260 °C) can be used.
Connection example of I2C interface
Address 3 Address 2 Address 1
EEP
ROM
LCD
driver
Color
sensor
SDA
SCL
www.DataSheet4U.com
Micro-controller
Cross section of WL-CSP
Glass
Si chip
Through-hole
electrode
Solder bump
Infrared-cut filter
Resin
SDA: serial data
SCL: serial clock
KPICC0164EA
KPICC0171EA
www.hamamatsu.com
1
1 page Color sensor
S11059-01WT
Condition 2 [¿xed period mode, high gain, Tint=01 (1.4 ms), integration time 1.4 ms/ch]
Command
Action
Data body
Ack
Remark
Address call (0x2A) S 0 1 0 1 0 1 0 W A 7-bit address
Register call (0x00)
0 0 0 0 0 0 0 0 A Calls control byte
Register write (0x89)
1 0 0 0 1 0 0 1 A ADC reset, standby disabled
Address call (0x2A) Sr 0 1 0 1 0 1 0 W A 7-bit address
Register call (0x00)
0 0 0 0 0 0 0 0 A Calls control byte
Resistor write (0x09)
0 0 0 0 1 0 0 1 A P ADC reset disabled, bus release
Wait longer than integration time (> 5.6 ms). Within this period, repeat measurement is continued.
Address call (0x2A) S 0 1 0 1 0 1 0 W A 7-bit address
Register call (0x03)
0 0 0 0 0 0 1 1 A Calls output data byte
Address call (0x2A) Sr 0 1 0 1 0 1 0 R A Changes to read mode
Data read out (R: MSB)
Data read out (R: LSB)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A
A
Red data output
Data read out (G: MSB)
Data read out (G: LSB)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A
A
Green data output
Data read out (B: MSB)
Data read out (B: LSB)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A
A
Blue data output
Data read out (Infrared: MSB) X
Data read out (Infrared: LSB) X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A-A
Infrared data output
P
SW==SWtarrittecomnodditeio(0n),,S-Ar==Rneosttaarctkncoonwdleitdiogne, A=Acknowledge, A=Acknowledge by host, P=Stop condition, R=Read mode(1),
Format
S
0x2A (7 bits)
WA
0x00
A 0x89 A
Sr
0x2A (7 bits)
WA
0x00
A 0x09 A P
Wait
S
0x2A (7 bits)
WA
0x03
A Sr 0x2A (7 bits) R A
Sensor data
A Sensor data A
Sensor data
A Sensor data A
Sensor data
A Sensor data A
Sensor data
A Sensor data A P
from master to slave
from slave to master
www.DataSheet4U.com
5
5 Page |
Páginas | Total 9 Páginas | |
PDF Descargar | [ Datasheet S11059-01WT.PDF ] |
Número de pieza | Descripción | Fabricantes |
S11059-01WT | I2C interface-compatible color sensor | Hamamatsu |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |