|
|
PDF W78LE52C Data sheet ( Hoja de datos )
| Número de pieza | W78LE52C | |
| Descripción | 8-BIT MICROCONTROLLER | |
| Fabricantes | Winbond | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de W78LE52C (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
|
No Preview Available !
W78LE52C/W78L052C
8-BIT MICROCONTROLLER
Table of Contents-
1. GENERAL DESCRIPTION ......................................................................................................... 2
2. FEATURES ................................................................................................................................. 2
3. PIN CONFIGURATIONS ............................................................................................................ 3
4. PIN DESCRIPTION..................................................................................................................... 4
5. FUNCTIONAL DESCRIPTION ................................................................................................... 5
6. ON-CHIP FLASH EPROM CHARACTERISTICS..................................................................... 10
7. SECURITY BITS ....................................................................................................................... 10
8. ABSOLUTE MAXIMUM RATINGS ........................................................................................... 11
9. DC CHARACTERISTICS.......................................................................................................... 12
10. AC CHARACTERISTICS .......................................................................................................... 14
11. TIMING WAVEFORMS ............................................................................................................. 17
12. TYPICAL APPLICATION CIRCUITS ........................................................................................ 19
13. PACKAGE DIMENSIONS ......................................................................................................... 21
14. REVISION HISTORY ................................................................................................................ 23
www.DataSheet.in
Publication Release Date: April 17, 2007
- 1 - Revision A4
1 page  
W78LE52C/W78L052C
5. FUNCTIONAL DESCRIPTION
The W78L052C architecture consists of a core controller surrounded by various registers, five general
purpose I/O ports, 256 bytes of RAM, three timer/counters, and a serial port. The processor supports
111 different opcodes and references both a 64K program address space and a 64K data storage
space.
Timers 0, 1, and 2
Timers 0, 1, and 2 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer 0,
TL1 and TH1 for Timer 1, and TL2 and TH2 for Timer 2. The TCON and TMOD registers provide
control functions for timers 0 and 1. The T2CON register provides control functions for Timer 2.
RCAP2H and RCAP2L are used as reload/capture registers for Timer 2.
The operations of Timer 0 and Timer 1 are the same as in the W78C51. Timer 2 is a special feature of
the W78L052C: it is a 16-bit timer/counter that is configured and controlled by the T2CON register.
Like Timers 0 and 1, Timer 2 can operate as either an external event counter or as an internal timer,
depending on the setting of bit C/T2 in T2CON. Timer 2 has three operating modes: capture, auto-
reload, and baud rate generator. The clock speed at capture or auto-reload mode is the same as that
of Timers 0 and 1.
New Defined Peripheral
In order to be more suitable for I/O, an extra 4-bit bit-addressable port P4 and two external interrupt
INT2 , INT3 has been added to either the PLCC or QFP 44 pin package. And description follows:
1. INT2 / INT3
Two additional external interrupts, INT2 and INT3 , whose functions are similar to those of external
interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are
determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register is
bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To
set/clear bits in the XICON register, one can use the "SETB (/CLR) bit" instruction. For example,
"SETB 0C2H" sets the EX2 bit of XICON.
XICON - external interrupt control (C0H)
PX3 EX3 IE3 IT3 PX2 EX2 IE2 IT2
PX3: External interrupt 3 priority high if set
EX3: External interrupt 3 enable if set
IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced
IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software
PX2: External interrupt 2 priority high if set
EX2: External interrupt 2 enable if set
IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced
IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software
www.DataSheet.in
Publication Release Date: April 17, 2007
- 5 - Revision A4
5 Page 
W78LE52C/W78L052C
Lock bit
This bit is used to protect the customer's program code in the W78L052C. It may be set after the
programmer finishes the programming and verifies sequence. Once this bit is set to logic 0, both the
Flash EPROM data and Special Setting Registers can not be accessed again.
MOVC Inhibit
This bit is used to restrict the accessible region of the MOVC instruction. It can prevent the MOVC
instruction in external program memory from reading the internal program code. When this bit is set to
logic 0, a MOVC instruction in external program memory space will be able to access code only in the
external memory, not in the internal memory. A MOVC instruction in internal program memory space
will always be able to access the ROM data in both internal and external memory. If this bit is logic 1,
there are no restrictions on the MOVC instruction.
Encryption
This bit is used to enable/disable the encryption logic for code protection. Once encryption feature is
enabled, the data presented on port 0 will be encoded via encryption logic. Only whole chip erase will
reset this bit.
8. ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
MIN.
MAX.
UNIT
DC Power Supply
Input Voltage
Operating Temperature
VDD−VSS
VIN
TA
-0.3
VSS -0.3
0
+7.0
VDD +0.3
70
V
V
°C
Storage Temperature
TST
-55
+150
°C
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability
of the device.
www.DataSheet.in
- 11 -
Publication Release Date: April 17, 2007
Revision A4
11 Page | ||
| Páginas | Total 23 Páginas | |
| PDF Descargar | [ Datasheet W78LE52C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| W78LE52 | 8-BIT MTP MICROCONTROLLER | Winbond |
| W78LE52 | 8-BIT MICROCONTROLLER | Winbond |
| W78LE52-24 | 8-BIT MTP MICROCONTROLLER | Winbond |
| W78LE52C | 8-BIT MICROCONTROLLER | Winbond |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |