DataSheet.es    


PDF V7X123-E-10 Data sheet ( Hoja de datos )

Número de pieza V7X123-E-10
Descripción HIGH VOLTAGE CHIP CAPACITORS
Fabricantes Superworld Electronics 
Logotipo Superworld Electronics Logotipo



Hay una vista previa y un enlace de descarga de V7X123-E-10 (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! V7X123-E-10 Hoja de datos, Descripción, Manual

HIGH VOLTAGE CHIP CAPACITORS
V7X SERIES
1. PART NO. EXPRESSION :
V7X103J-B-10
(a) (b) (c) (d) (e) (f)
(a) Chip Size
(b) Temp. Coefficient : X ( ±15% )
( Temp. range : -55°C to +125°C )
(c) Capacitance code : 103 = 10000pF
(d) Tolerance code
(e) Voltage code : B = 200Vdc
(f) 10 : Lead Free
2. CONFIGURATION & DIMENSIONS :
A
D
L
G
B
PCB Pattern
Unit:m/m
ABCDGH L
4.60±0.30 3.20±0.30 3.00 Max. 0.30 Min. 2.80 - 3.40 2.30 - 3.00 1.80 - 2.00
3. SCHEMATIC :
4. MATERIALS :
ba
Ag(100%)
Ni(100%)-1.5um(min.)
Sn(100%)-3.0um(min.)
(a) Body : Ceramic
(b) Termination : Ag/Ni/Sn
5. GENERAL SPECIFICATION :
a) Storage temp. : +5°C to +40°C
b) Operating temp. : -55°C to +125°C
c) Resistance to solder heat : 260°C.10secs
NOTE : Specifications subject to change without notice. Please check our website for latest information.
15.01.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
www.DataSheet.in

1 page




V7X123-E-10 pdf
HIGH VOLTAGE CHIP CAPACITORS
6. ELECTRICAL CHARACTERISTICS : ( Rated Voltage : 1KVdc )
Part Number
Capacitance
( pF )
V7X221 -J-10
220
V7X271 -J-10
270
V7X331 -J-10
330
V7X391 -J-10
390
V7X471 -J-10
470
V7X561 -J-10
560
V7X681 -J-10
680
V7X102 -J-10
1000
V7X122 -J-10
1200
V7X152 -J-10
1500
V7X182 -J-10
1800
V7X222 -J-10
2200
V7X272 -J-10
2700
V7X332 -J-10
3300
V7X392 -J-10
3900
V7X472 -J-10
4700
V7X562 -J-10
5600
V7X682 -J-10
6800
V7X103 -J-10
10000
V7X123 -J-10
12000
Tolerance code :
: C : ±0.25pF
D : ±0.50pF
J : ±5%
K : ±10%
M : ±20%
Part Number
V7X153 -J-10
V7X183 -J-10
V7X223 -J-10
V7X273 -J-10
V7X333 -J-10
V7X393 -J-10
V7X473 -J-10
V7X563 -J-10
V7X683 -J-10
V7X104 -J-10
V7X SERIES
Capacitance
( pF )
15000
18000
22000
27000
33000
39000
47000
56000
68000
100000
NOTE : Specifications subject to change without notice. Please check our website for latest information.
15.01.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5
www.DataSheet.in

5 Page





V7X123-E-10 arduino
HIGH VOLTAGE CHIP CAPACITORS
V7X SERIES
8. SOLDERIND AND MOUNTING :
8-1 Re-flow Soldering :
Preheat and gradual increase in temp. to the reflow temp. is recommended to decrease the potential of the thermal crack
on the components. The recommended heating rate depends on the size of the component, however it should not
exceed 3°C/sec.
8-2 Wave Soldering :
Most of the components are wave soldered with solder at 230~250°C. Adequate care must be taken to prevent the
potential of thermal cracks on the ceramic capacitors. Refer to Figure 2 for optimum soldering benefits.
8-3 Hand Soldering :
Sudden temp. change in components, results in a temp. gradient, and therefore may cause internal thermal cracks in the
components. In general a hand soldering method is not recommend unless proper preheating and handling practices have
been taken. Care must also be taken not to touch the ceramic body of the capacitor with the tip of solder iron.
How to solder repair by solder iron :
1) Selection of soldering iron tip
The required temp. of solder iron for any type of repair depends on the type of the tip, the substrate material, and the
solder land size
2) recommended solder iron condition
a) Preheat substrate to (60°C~120°C).
b) 350°C tip temperature (max)
c) Never contact the ceramic with the iron tip
d) 3.0mm tip diameter (max)
e) Use a 30 watt (max.) soldering iron with tip diameter of 3.0mm
f) Limit soldering time to 5 secs.
Cooling condition :
Natural cooling using air is recommended. If the chips are dipped into a solvent for cleaning, the temp. difference
between the solvent and the chips must be less than 100°C.
Preheating
260
217
Soldering
Natural
cooling
Preheating
300
250
230
200
Soldering
Natural
cooling
Over
1min.
Over
1min.
Gradual Cooling
70-90secs
Figure 1. Re-flow Soldering
Over 2mins.
Over 1min
2-3secs.
Figure 2. Wave Soldering
Preheating
350
250
200
Soldering
Natural
cooling
Within 5secs.
Figure 3. Hand Soldering
NOTE : Specifications subject to change without notice. Please check our website for latest information.
15.01.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 11
www.DataSheet.in

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet V7X123-E-10.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
V7X123-E-10HIGH VOLTAGE CHIP CAPACITORSSuperworld Electronics
Superworld Electronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar