|
|
PDF NCP1599 Data sheet ( Hoja de datos )
| Número de pieza | NCP1599 | |
| Descripción | 3 A Synchronous Buck Regulator | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de NCP1599 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
NCP1599
www.DataSheet4U.com
Product Preview
1 MHz, 3 A Synchronous
Buck Regulator
The NCP1599 is a fixed 1 MHz, high−output−current, synchronous
PWM converter that integrates a low−resistance, high−side P−channel
MOSFET and a low−side N−channel MOSFET. The NCP1599 utilizes
internally compensated current mode control to provide good transient
response, ease of implementation, and excellent loop stability. It
regulates input voltages from 2.8 V to 5.5 V down to an output voltage
as low as 0.8 V and is able to supply up to 3.0 A of load current.
The NCP1599 includes an internally fixed switching frequency
(FSW), and an internal soft−start to limit inrush current.
Other features include cycle−by−cycle current limiting,
short−circuit protection, power saving mode and thermal shutdown.
Features
• Wide Input Voltage Range: from 2.8 V to 5.5 V
• Internal 140 mW High−Side P−Channel and 90 mW Low−Side
N−Channel MOSFET
• Fixed 1 MHz Switching Frequency
• Cycle−by−Cycle Current Limiting
• Hiccup Mode Short−Circuit Protection
• Overtemperature Protection
• Internal Soft−Start
• Start−up with Pre−Biased Output Load
• Adjustable Output Voltage Down to 0.8 V
• Power Saving Mode During Light Load
• These are Pb−Free Devices
Applications
• DSP Power
• Hard Disk Drivers
• Computer Peripherals
• Home Audio
• Set−Top Boxes
• Networking Equipment
• LCD TV
• Wireless and DSL/Cable Modem
• USB Power Devices
http://onsemi.com
1
DFN6
CASE 506AH
MARKING
DIAGRAM
1 1599
AYWW
G
A = Assembly Location
Y = Year
WW = Work Week
G = Pb−Free Package
PIN CONNECTIONS
FB 1
6 COMP
GND 2
5 VCC
LX 3
4 VCCP
(Top View)
ORDERING INFORMATION
Device
Package
Shipping†
NCP1599MNR2G DFN6 3000 / Tape & Reel
(Pb−Free)
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
© Semiconductor Components Industries, LLC, 2010
May, 2010 − Rev. P0
1
Publication Order Number:
NCP1599/D
1 page  
NCP1599
DETAILED DESCRIPTION
www.DataSheet4U.com
Overview
The NCP1599 is a synchronous PWM controller that
incorporates all the control and protection circuitry
necessary to satisfy a wide range of applications. The
NCP1599 employs current mode control to provide good
transient response, simple compensation, and excellent
stability. The features of the NCP1599 include a precision
reference, fixed 1 MHz switching frequency, a
transconductance error amplifier, an integrated high−side
P−channel MOSFET and low−side N−Channel MOSFET,
internal soft−start, and very low shutdown current. The
protection features of the NCP1599 include internal
soft−start, pulse−by−pulse current limit, hiccup mode
short−circuit protection, and thermal shutdown.
Reference Voltage
The NCP1599 incorporates an internal reference that
allows output voltages as low as 0.8 V. The tolerance of the
internal reference is guaranteed over the entire operating
temperature range of the controller. The reference voltage is
trimmed using a test configuration that accounts for error
amplifier offset and bias currents.
Oscillator Frequency
A fixed precision oscillator is provided. The oscillator
frequency range is 1 MHz with ±13% variation.
Transconductance Error Amplifier
The transconductance error amplifier’s primary function
is to regulate the converter’s output voltage using a resistor
divider connected from the converter’s output to the FB pin
of the controller, as shown in the applications Schematic. A
series RC compensation network must be connected from
the error amplifier’s output (COMP pin) to GND to stabilize
the converter. In some applications, a lower value capacitor
may be connected from the COMP pin to GND to reduce the
loop gain at higher frequencies. However, if this capacitor
is too large the phase margin of the converter will be
reduced. If a Fault occurs, the COMP pin is immediately
pulled to GND and PWM switching is inhibited.
Output MOSFETs
The NCP1599 includes low RDS(on), both high−side
P−channel and low−side N−channel MOSFETs capable of
delivering up to 3.0 A of current. When the controller is
disabled or during a Fault condition, the controller’s output
stage is tri−stated by turning OFF both the upper and lower
MOSFETs.
Adaptive Dead Time Gate Driver
In a synchronous buck converter, a certain dead time is
required between the low side drive signal and high side
drive signal to avoid shoot through. During the dead time,
the body diode of the low side FET freewheels the current.
The body diode has much higher voltage drop than that of
the MOSFET, which reduces the efficiency significantly.
The longer the body diode conducts, the lower the
efficiency. In NCP1599, the drivers and MOSFETs are
integrated in a single chip. The parasitic inductance is
minimized. Adaptive dead time control method is used in
NCP1599 to prevent the shoot through from happening and
minimizing the diode conduction loss at the same time.
Pulse Width Modulation
A high−speed PWM comparator, capable of pulse widths
as low as 50 ns, is included in the NCP1599. The inverting
input of the comparator is connected to the output of the
error amplifier. The non−inverting input is connected to the
the current sense signal. At the beginning of each PWM
cycle, the CLK signal sets the PWM flip−flop and the upper
MOSFET is turned ON. When the current sense signal rises
above the error amplifier’s voltage then the comparator will
reset the PWM flip−flop and the upper MOSFET will be
turned OFF.
Power Save Mode
If the load current decreases, the converter will enter
power save mode operation automatically. During power
save mode, the converter skips switching and operates with
reduced frequency, which minimizes the quiescent current
and maintain high efficiency.
Internal Soft−Start
To limit the startup inrush current, an internal soft start
circuit is used to ramp up the reference voltage from 0 V to
its final value linearly. The internal soft start time is 1 ms
typically.
Current Sense Amplifier
The NCP1599 monitors the current in the upper
MOSFET. The current signal is required by the PWM
comparator, the pulse−by−pulse current limiter, and the
hiccup mode/over current counter.
http://onsemi.com
5
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet NCP1599.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| NCP1592 | Synchronous Buck PWM Switcher | ON Semiconductor |
| NCP1593A | Synchronous Buck Regulator | ON Semiconductor |
| NCP1593B | Synchronous Buck Regulator | ON Semiconductor |
| NCP1595 | Current Mode PWM Converter | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |