DataSheet.es    


PDF 73S8014R Data sheet ( Hoja de datos )

Número de pieza 73S8014R
Descripción Smart Card Interface
Fabricantes Teridian Semiconductor 
Logotipo Teridian Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de 73S8014R (archivo pdf) en la parte inferior de esta página.


Total 29 Páginas

No Preview Available ! 73S8014R Hoja de datos, Descripción, Manual

Simplifying System Integration™
www.DataSheet4U.com
73S8014R
Smart Card Interface
DATA SHEET
September 2008
DESCRIPTION
The Teridian 73S8014R is a single smart card (ICC) interface
circuit, firmware compatible with 8024-type devices for
configurations where only asynchronous cards must be
supported. It is derived from the 73S8024RN industry-
standard electrical interface. The 73S8014R has been
optimized to match most of the typical Set-Top-Box / A/V
Conditional Access applications. Optimization essentially
involved a smaller pin-count, support for single I/O, and
maximum card current of 65mA (ISO-7816 / EMV
compliance).
The 73S8014R interfaces with the host processor through the
same bus (digital I/Os) as the 73S8024RN, which is
compatible with any other 8024-type IC. As a result, the
73S8014R is a very attractive cost-reduction path from
traditional 8024 ICs. The 73S8014R has been designed to
provide full electrical compliance with ISO 7816-3 and EMV
4.0 specifications.
Interfacing with the system controller is done through a
control bus, composed of digital inputs to control the
interface, and one interrupt output to inform the system
controller of the card presence and faults.
The card clock can be generated by an on-chip oscillator
using an external crystal or by connection to an externally
supplied clock signal.
The 73S8014R incorporates an ISO 7816-3
activation/deactivation sequencer that controls the card
signals. Level-shifters drive the card signals with the
selected card voltage (3V or 5V), coming from an internal
Low Drop-Out (LDO) voltage regulator. This LDO regulator is
powered by a dedicated power supply input VPC. Digital
circuitry is powered separately by a digital power supply VDD.
With its embedded LDO regulator, the 73S8024RN is a
cost-effective solution for any application where a 5V
(typically -5% +10%) power supply is available.
Emergency card deactivation is initiated upon card extraction
or upon any fault detected by the protection circuitry. The
fault can be a card over-current, VCC undervoltage or power
supply fault (VDD). The card over-current circuitry is a true
current detection function, as opposed to VCC voltage drop
detection, as usually implemented in non-Teridian 8024
interface ICs.
The VDD voltage fault has a threshold voltage that can be
adjusted with an external resistor network. It allows
automated card deactivation at a customized VDD voltage
threshold value. It can be used, for instance, to match the
system controller operating voltage range.
APPLICATIONS
Set-Top-Box Conditional Access and Pay-per-View
General purpose smart card readers
ADVANTAGES
Same advantages as the Teridian 73S80xxR family:
ƒ VCC card generated by an LDO regulator
ƒ Very low power dissipation (saves up to 1/2W)
ƒ Fewer external components are required
ƒ Better noise performance
True card over-current detection
Firmware compatibility with all 8024 ICs
Small format 20SO package
FEATURES
Card Interface:
ƒ Complies with ISO 7816-3 and EMV 4.0
ƒ Supports 3V / 5V cards
ƒ ISO 7816-3 Activation / Deactivation sequencer
ƒ Automated deactivation upon hardware fault (i.e. upon
drop on VDD power supply or card overcurrent)
ƒ The VDD voltage supervisor threshold value (fault) can
be externally adjusted
ƒ Over-current detection 130mA max
ƒ Card CLK clock frequency up to 20MHz
System Controller Interface:
ƒ 3 Digital inputs control the card activation /
deactivation, card reset and card voltage
ƒ 2 Digital inputs control the card clock frequency
ƒ 1 Digital output, interrupt to the system controller,
reports to the host the card presence and faults
ƒ Crystal oscillator or host clock, up to 27MHz
Regulator Power Supply:
ƒ 4.75V to 5.5V
Digital Interfacing: 2.7V to 5.5V
6kV ESD protection on the card interface
Package: SO 20-pin
RoHS compliant (6/6) lead-free package
Rev. 1.0
© 2008 Teridian Semiconductor Corporation
1

1 page




73S8014R pdf
DS_8014R_012
1 Pinout
The 73S8014R is supplied as a 20-pin SO package.
OFF
1
20
RSTIN
I/OUC
2
3
19
18
VPC
CLKDIV2
CMDVCC
5V/#V
GND
XTALIN
4 17
5 16
73S8014R
6 15
7 14
8 13
9 12
XTALOUT
10
11
Figure 2: 73S8014R 20-SOP Pin Out
www.DataSheet4U.com
73S8014R Data Sheet
CLKDIV1
PRES
VCC
CLK
GND
RST
I/O
VDD
VDDF_ADJ
GND
Rev. 1.0
5

5 Page





73S8014R arduino
DS_8014R_012
www.DataSheet4U.com
73S8014R Data Sheet
Symbol
Parameter
Condition
Reset and Clock for card interface, RST, CLK
VOH Output level, high
IOH =-200μA
VOL Output level, low
IOL=200μA
VINACT
IRST_LIM
ICLK_LIM
CLKSR3V
Output voltage when outside
of session
Output current limit, RST
Output current limit, CLK
CLK slew rate
IOL = 0
IOL = 1mA
Vcc = 3V
CLKSR5V CLK slew rate
tR, tF
Output rise time, fall time
δ Duty cycle for CLK
Vcc = 5V
CL = 35pF for CLK,
10% to 90%
CL = 200pF for RST,
10% to 90%
CL =35pF,
FCLK 20MHz
Min
0.9 VCC
0
0.3
0.5
45
Nom
Max
Unit
VCC
0.15 VCC
0.1
0.3
30
70
8
V
V
V
V
mA
mA
V/ns
V/ns
ns
100 ns
55 %
2.5 Characteristics: Digital Signals
Table 6 lists the 73S8014R digital signals characteristics.
Table 6: Digital Signals Characteristics
Symbol
Parameter
Condition
Digital I/O except for XTALIN and XTALOUT
VIL Input Low Voltage
VIH Input High Voltage
VOL Output Low Voltage
IOL = 2mA
VOH
ROUT
|IIL1|
Output High Voltage
Pull-up resistor, OFF
Input Leakage Current
IOH = -1mA
GND < VIN < VDD
Min
-0.3
1.8
VDD - 0.45
16
-5
Nom
20
Max
0.8
VDD + 0.3
0.45
24
5
Unit
V
V
V
V
kΩ
μA
Rev. 1.0
11

11 Page







PáginasTotal 29 Páginas
PDF Descargar[ Datasheet 73S8014R.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
73S8014RSmart Card InterfaceTeridian Semiconductor
Teridian Semiconductor
73S8014RNSmart Card InterfaceTeridian Semiconductor
Teridian Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar