DataSheet.es    


PDF B66414 Data sheet ( Hoja de datos )

Número de pieza B66414
Descripción Ferrites and accessories
Fabricantes EPCOS 
Logotipo EPCOS Logotipo



Hay una vista previa y un enlace de descarga de B66414 (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! B66414 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
Ferrites and accessories
EFD 15/8/5
Core and accessories
Series/Type:
B66413, B66414
Date:
September 2006/June 2007
Data Sheet
EPCOS AG 2006. Reproduction, publication and dissemination of this data sheet and the
information contained therein without EPCOS’ prior express consent is prohibited.

1 page




B66414 pdf
Ferrites and accessories
Cautions and warnings
www.DataSheet4U.com
Mechanical stress and mounting
Ferrite cores have to meet mechanical requirements during assembling and for a growing number
of applications. Since ferrites are ceramic materials one has to be aware of the special behavior
under mechanical load.
As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing
or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads
can cause cracks or failure of the ferrite cores.
For detailed information see Data Book 2007, chapter “General – Definitions, 8.1”.
Effects of core combination on AL value
Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent
that the initial permeability is dependent on the stress state of the core. The higher the stresses are
in the core, the lower is the value for the initial permeability. Thus the embedding medium should
have the greatest possible elasticity.
For detailed information see Data Book 2007, chapter “General – Definitions, 8.2”.
Heating up
Ferrites can run hot during operation at higher flux densities and higher frequencies.
NiZn-materials
The magnetic properties of NiZn-materials can change irreversible in high magnetic fields.
Processing notes
– The start of the winding process should be soft. Else the flanges may be destroid.
– To strong winding forces may blast the flanges or squeeze the tube that the cores can no more
be mount.
– To long soldering time at high temperature (>300 °C) may effect coplanarity or pin arrangement.
– Not following the processing notes for soldering of the J-leg terminals may cause solderability
problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation
of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”.
– The dimensions of the hole arrangement have fixed values and should be understood as a
recommendation for drilling the printed circuit board. For dimensioning the pins, the group of
holes can only be seen under certain conditions, as they fit into the given hole arrangement. To
avoid problems when mounting the transformer, the manufacturing tolerances for positioning the
customers’ drilling process must be considered by increasing the hole diameter.
5 09/06

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet B66414.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
B66411EFD 10/5/3 CoreEPCOS
EPCOS
B66413Ferrites and accessoriesEPCOS
EPCOS
B66414Ferrites and accessoriesEPCOS
EPCOS
B66417Ferrites and accessoriesEPCOS
EPCOS

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar