|
|
Número de pieza | NCP51460 | |
Descripción | 2.0 Amp PLC Line Driver | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NCP51460 (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
No Preview Available ! NCS5650
www.DataSheet4U.com
2 Amp PLC Line Driver
The NCS5650 is a high efficiency, Class A/B, low distortion power
line driver. Its design is optimized to accept a signal from a Power Line
Carrier modem. The output stage is designed to drive up to 2 A peak
into an isolation transformer or simple coil coupling to the mains. At
output current of 1.5 A, the output voltage is guaranteed to swing
within 1 V or less of either rail giving the user improved SNR. Power
supply options are single−sided 6 V to 12 V and dual balanced
$3.0 V to $6.0 V. The input stage contains an operational amplifier
which can be configured as a unity gain follower buffer or used to
provide the first stage of a 4−pole low pass filter. In addition the
NCS5650 offers a current limit programmable with a single resistor,
R−Limit, together with a current limit flag.
The device provides two independent thermal flags with hysteresis:
a thermal warning flag to let the user know the internal junction
temperature has reached a user programmable thermal warning
threshold and a thermal error flag that indicates the internal junction
temperature has exceeded 150°C. In shutdown mode the NCS5650
output goes into a high−impedance state. The NCS5650 comes in a 20
lead QFN package (4x4x1mm) with an exposed thermal pad for
enhanced thermal reliability.
Features
• Rail−to−Rail Drop of Only $1 V with Iout = 1.5 A
• VCC: Single−Sided (6 V to 12 V) or Dual−Balanced $6.0 V
• Flexible 4th−Order Filtering
• Current−Limit Set with One Resistor
• Diagnostic Flags Level Shifted to V_mc to Simplify Interface with
External MCU
♦ Thermal Warning Flag with Flexible Threshold Setting
♦ Thermal Error flag and Shutdown
♦ Overcurrent Flag
• Enable/Shutdown Control
• Extended Junction Temperature Range: −40°C to +125°C
• Small Package: 20−pin 4x4x1mm QFN with Exposed Thermal Pad
• Optimized for Operation in the Cenelec A to D Frequency Band
• This is a Pb−Free Device
Typical Applications
• Power Line Communication Driver in AMM and AMR Metering
Systems
• Valve, Actuator, and Motor Driver
• Audio
http://onsemi.com
1 20
QFN20
CASE 485E
MARKING
DIAGRAM
20
1 NCS
5650
ALYWG
G
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
G = Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
Device
Package
Shipping
NCS5650MNTXG QFN20 3000 / Tape & Reel
(Pb−Free)
†For information on tape and reel specifications,
including part or orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2010
May, 2010 − Rev. 0
1
Publication Order Number:
NCS5650/D
1 page NCS5650
www.DataSheet4U.com
ELECTRICAL CHARACTERISTICS VS = 12 V All limits apply over the temperature range, TJ = –40°C to +125°C, unless
otherwise noted. Total supply VS = VCC − VEE.
NCS5650
Parameter
Symbol
Condition
OUTPUT OPERATIONAL AMPLIFIER (Op Amp B)
Input Impedance
Differential
Common−Mode
Open−Loop Gain (Note 2)
Frequency Response
RL = 5 W
Gain Bandwidth Product
GBW
Full Power Bandwidth (Note 2)
Slew Rate
SR
G = +2, Vout = 11 VPP
Total Harmonic Distortion + Noise THD+N
Output
G = +1, RL = 50 W,
VO = 8 VPP, f = 1 kHz
G = +1, RL = 50 W,
VO = 8 VPP, f = 100 kHz
Voltage Output Swing from Rail
From Positive Rail
From Negative Rail
Voltage Output Swing from Rail
From Positive Rail
Negative Rail
Output Impedance
Enabled Mode
Shutdown Mode
VOH
VOL
VOH
VOL
Z0
VCC = +12 V, VEE = 0 V
Iout = 1.5 A to Mid−Supply
Iout = 1.5 A to Mid−Supply
VCC = +6 V, VEE = −6 V
Iout = 1.5 A to GND
Iout = 1.5 A to GND
Closed Loop G = +1,
f = 100 kHz
Capacitive Load Drive
BOTH AMPLIFIERS COMBINED
CLOAD
Junction Temperature
At Shutdown (Note 2)
TJ
At Recovery from Shutdown
Thermal Warning Tolerance
Twarning is determined by the ratio of
two resistors (see Figure 8) (Note 3)
Min
80
200
+150
Typ
0.2 | 11
0.2 | 22
100
60
400
70
0.015
0.067
0.7
0.4
0.7
0.4
0.065
12
500
+160
+135
±10
Max Units
GW | pF
GW | pF
dB
MHz
kHz
V/ms
%
1V
1V
1V
1V
W
MW
nF
°C
°C
°C
Current Limit Tolerance
I−Limit is determined by a single
resistor (see Figure 5 text) (Note 3)
±50
mA
Power Supply
Operating Voltage Range
VS
Quiescent Current
Enabled Mode
Shutdown Mode
VCOM
IQ
Single−tSouSpypslyteOmpCeroamtiomno(nV)EE Tied
Dual Balanced−Supply operation
VCC = +6 V, VEE = −6 V
VCC = 12 V, VEE = 0 V
Internal resistor divider.
Bypass purposes only.
6 to 12
13.2
±3.0 to ±6.0
20 40
120 150
5.8 6.0
6.2
V
mA
mA
V
2. Guaranteed by characterization or design.
3. Formula accuracy requires a resistor with $1% tolerance.
http://onsemi.com
5
5 Page |
Páginas | Total 9 Páginas | |
PDF Descargar | [ Datasheet NCP51460.PDF ] |
Número de pieza | Descripción | Fabricantes |
NCP51460 | 2.0 Amp PLC Line Driver | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |