|
|
PDF 25VF016B Data sheet ( Hoja de datos )
| Número de pieza | 25VF016B | |
| Descripción | SST25VF016B | |
| Fabricantes | Silicon Storage Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de 25VF016B (archivo pdf) en la parte inferior de esta página. Total 28 Páginas | ||
|
No Preview Available !
16 Mbit SPI Serial Flash
SST25VF016B
FEATURES:
SST25VF016B16Mb Serial Peripheral Interface (SPI) flash memory
Preliminary Specifications
• Single Voltage Read and Write Operations
– 2.7-3.6V
• Serial Interface Architecture
– SPI Compatible: Mode 0 and Mode 3
• High Speed Clock Frequency
– 50 MHz
• Superior Reliability
– Endurance: 100,000 Cycles (typical)
– Greater than 100 years Data Retention
• Low Power Consumption:
www.Data–ShAeectt4ivUe.cRomead Current: 10 mA (typical)
– Standby Current: 5 µA (typical)
• Flexible Erase Capability
– Uniform 4 KByte sectors
– Uniform 32 KByte overlay blocks
– Uniform 64 KByte overlay blocks
• Fast Erase and Byte-Program:
– Chip-Erase Time: 35 ms (typical)
– Sector-/Block-Erase Time: 18 ms (typical)
– Byte-Program Time: 7 µs (typical)
• Auto Address Increment (AAI) Programming
– Decrease total chip programming time over
Byte-Program operations
• End-of-Write Detection
– Software polling the BUSY bit in Status Register
– Busy Status readout on SO pin in AAI Mode
• Hold Pin (HOLD#)
– Suspends a serial sequence to the memory
without deselecting the device
• Write Protection (WP#)
– Enables/Disables the Lock-Down function of the
status register
• Software Write Protection
– Write protection through Block-Protection bits in
status register
• Temperature Range
– Commercial: 0°C to +70°C
– Industrial: -40°C to +85°C
• Packages Available
– 8-lead SOIC (200 mils)
– 8-contact WSON (6mm x 5mm)
• All non-Pb (lead-free) devices are RoHS compliant
PRODUCT DESCRIPTION
SST’s 25 series Serial Flash family features a four-wire,
SPI-compatible interface that allows for a low pin-count
package which occupies less board space and ultimately
lowers total system costs. The SST25VF016B devices are
enhanced with improved operating frequency and even
lower power consumption than the original SST25VFxxxA
devices. SST25VF016B SPI serial flash memories are
manufactured with SST’s proprietary, high-performance
CMOS SuperFlash technology. The split-gate cell design
and thick-oxide tunneling injector attain better reliability and
manufacturability compared with alternate approaches.
The SST25VF016B devices significantly improve perfor-
mance and reliability, while lowering power consumption.
The devices write (Program or Erase) with a single power
supply of 2.7-3.6V for SST25VF016B. The total energy
consumed is a function of the applied voltage, current, and
time of application. Since for any given voltage range, the
SuperFlash technology uses less current to program and
has a shorter erase time, the total energy consumed during
any Erase or Program operation is less than alternative
flash memory technologies.
The SST25VF016B device is offered in both 8-lead SOIC
(200 mils) and 8-contact WSON (6mm x 5mm) packages.
See Figure 1 for pin assignments.
©2005 Silicon Storage Technology, Inc.
S71271-01-000
9/05
1
The SST logo and SuperFlash are registered Trademarks of Silicon Storage Technology, Inc.
These specifications are subject to change without notice.
1 page  
16 Mbit SPI Serial Flash
SST25VF016B
Hold Operation
The HOLD# pin is used to pause a serial sequence under-
way with the SPI flash memory without resetting the clock-
ing sequence. To activate the HOLD# mode, CE# must be
in active low state. The HOLD# mode begins when the
SCK active low state coincides with the falling edge of the
HOLD# signal. The HOLD mode ends when the HOLD#
signal’s rising edge coincides with the SCK active low state.
If the falling edge of the HOLD# signal does not coincide
with the SCK active low state, then the device enters Hold
mode when the SCK next reaches the active low state.
www.DSaitmaiSlahrelye,t4ifUt.hceomrising edge of the HOLD# signal does not
Preliminary Specifications
coincide with the SCK active low state, then the device
exits in Hold mode when the SCK next reaches the active
low state. See Figure 3 for Hold Condition waveform.
Once the device enters Hold mode, SO will be in high-
impedance state while SI and SCK can be VIL or VIH.
If CE# is driven active high during a Hold condition, it resets
the internal logic of the device. As long as HOLD# signal is
low, the memory remains in the Hold condition. To resume
communication with the device, HOLD# must be driven
active high, and CE# must be driven active low. See Figure
23 for Hold timing.
SCK
HOLD#
Active
Hold
FIGURE 3: HOLD CONDITION WAVEFORM
Active
Hold
Active
1271 HoldCond.0
Write Protection
SST25VF016B provides software Write protection. The
Write Protect pin (WP#) enables or disables the lock-down
function of the status register. The Block-Protection bits
(BP3, BP2, BP1, BP0, and BPL) in the status register pro-
vide Write protection to the memory array and the status
register. See Table 4 for the Block-Protection description.
Write Protect Pin (WP#)
The Write Protect (WP#) pin enables the lock-down func-
tion of the BPL bit (bit 7) in the status register. When WP#
is driven low, the execution of the Write-Status-Register
(WRSR) instruction is determined by the value of the BPL
bit (see Table 2). When WP# is high, the lock-down func-
tion of the BPL bit is disabled.
TABLE 2: CONDITIONS TO EXECUTE WRITE-STATUS-
REGISTER (WRSR) INSTRUCTION
WP#
L
L
H
BPL
1
0
X
Execute WRSR Instruction
Not Allowed
Allowed
Allowed
T2.0 1271
©2005 Silicon Storage Technology, Inc.
5
S71271-01-000
9/05
5 Page 
16 Mbit SPI Serial Flash
SST25VF016B
Byte-Program
The Byte-Program instruction programs the bits in the
selected byte to the desired data. The selected byte must
be in the erased state (FFH) when initiating a Program
operation. A Byte-Program instruction applied to a pro-
tected memory area will be ignored.
Prior to any Write operation, the Write-Enable (WREN)
instruction must be executed. CE# must remain active low
for the duration of the Byte-Program instruction. The Byte-
Preliminary Specifications
Program instruction is initiated by executing an 8-bit com-
mand, 02H, followed by address bits [A23-A0]. Following the
address, the data is input in order from MSB (bit 7) to LSB
(bit 0). CE# must be driven high before the instruction is
executed. The user may poll the Busy bit in the software
status register or wait TBP for the completion of the internal
self-timed Byte-Program operation. See Figure 6 for the
Byte-Program sequence.
www.DataSheet4U.com
CE#
MODE 3
SCK MODE 0
0 1 2345 6 78
15 16
23 24 31 32 39
SI 02
MSB
SO
FIGURE 6: BYTE-PROGRAM SEQUENCE
ADD.
MSB
ADD.
HIGH IMPEDANCE
ADD. DIN
MSB LSB
1271 ByteProg.0
©2005 Silicon Storage Technology, Inc.
11
S71271-01-000
9/05
11 Page | ||
| Páginas | Total 28 Páginas | |
| PDF Descargar | [ Datasheet 25VF016B.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| 25VF016B | SST25VF016B | Silicon Storage Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |