DataSheet.es    


PDF CFD-G770CP Data sheet ( Hoja de datos )

Número de pieza CFD-G770CP
Descripción CD RADIO CASSETTE-CORDER
Fabricantes Sony 
Logotipo Sony Logotipo



Hay una vista previa y un enlace de descarga de CFD-G770CP (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! CFD-G770CP Hoja de datos, Descripción, Manual

SERVICE MANUAL
Ver. 1.0 2007.03
CFD-G700CP/G770CP/
G770CPKwww.DataSheet4U.com
US Model
CFD-G700CP
Canadian Model
CFD-G770CPK
E Model
CFD-G770CP/G770CPK
Australian Model
CFD-G770CPK
Photo : CFD-G770CPK
CD
Section
TAPE
Section
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Type
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
CFD-G505/G555CP/G555CPK
KSM-213CDP/C2NP
KSS-213C
HCD-EC50
H21SB-C05
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 3.2-ohm loads, both channels driven from
1 000 - 10 000 Hz; rated 3 W per channel-minimum
RMS power, with no more than 10 % total harmonic
distortion in AC operation.
Woofer with 4-ohm loads, driven from 50 - 150
Hz; rated 6 W minimum RMS power, with no more
than 10 % total harmonic distortion in AC
operation.
Other specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(Th is output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and fl utter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1 710 kHz
(G700CP: US/G770CPK: CND, MX, E92)
AM: 531 - 1 611 kHz (G770CPK: AUS)
AM: 531 - 1 611 kHz (9 kHz step)(G770CP)
AM: 530 - 1 610 kHz (10 kHz step)(G770CP)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 150 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 10 cm (4 in.) dia., 3.2 ,
cone type (2)
Woofer: 13 cm (5 1/8 in.) dia., 4 ,
cone type (1)
Tweeter: 2 cm (13/16 in.) dia. (2)
Input
Built-in audio cable with stereo-mini plug:
Minimum input level 245 mV
AUDIO IN Jack (stereo minijack):
Minimum input level 245 mV
MIC MIX (microphone) jack (monaural minijack):
Sensitivity 2.5 mV, for low impedance
microphone
Minimum input level 2.5 mV (G770CPK)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 impedance headphones
Power output
4 W + 4 W (at 3.2 , 10% harmonic distortion)
Woofer:
12 W (at 4 , 10% harmonic distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz
(G700CP: US/G770CPK: CND, MX, E92)
230 - 240 V AC, 50 Hz (G700CP: SP)
230 V AC, 50 Hz
(G700CP: E41/G770CPK: AUS)
12 V DC, 8 R20 (size D) batteries
For remote control:
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 28 W
— Continued on next page —
• Abbreviation
AUS : Australian model
E92 : AC 120V area in E model
CND : Canadian model
MX : Mexican model
E41 : AC 230V area in E model SP : Singapore model
CD RADIO CASSETTE-CORDER
9-887-620-01
2007C16-1
© 2007.03
Sony Corporation
Personal Audio Division
Published by Sony Techno Create Corporation

1 page




CFD-G770CP pdf
SECTION 2
GENERAL
CFD-G700CP/G770CP/G770CPK
wwwTh.DisatsaeSchteioent4Uis.ceoxmtracted
from instruction manual.
CFD-G700CP (1/2)
Basic Operations
* VOL + (VOLUME + on the remote) Ȳ, ā Ȱ and à Ȫ (on the
unit) have a tactile dot.
Before using the unit
To turn on/off the power
Press POWER ȩ.
To adjust the volume
Press VOL +, – (VOLUME +, – on the remote) Ȳ.
To listen through headphones
Connect the headphones to the ­ (headphones) jack ȼ.
To select the sound characteristic
Press ROCK, DANCE, SALSA, REGGAETON or FLAT
Ȭ to select the kind of audio emphasis that you want.
(On the remote, press SOUND Ȭ repeatedly.)
To reinforce the bass sound
Press POWER DRIVE WOOFER (WOOFER on
the remote) ȸ to select
or
on
the display.
is more effective. When the
WOOFER function works, the ring on the front panel
lights up.
To return to normal sound, press the button repeatedly
until the indication disappears from the display.
Notes
ˎ While the sleeping timer is on, the ring does not light, even if the
WOOFER function is used.
ˎ When you use the headphones, the WOOFER function does not
work.
Playing a CD/MP3 disc
1 Press ì PUSH OPEN/CLOSE ȱ on the unit, and
place a disc with the label side up on the CD
compartment.
To close the CD compartment, press ì PUSH OPEN/
CLOSE ȱ on the unit.
2 Press ā on the unit (à on the remote) Ȱ.
The unit plays all the tracks/MP3 files once.
When you place MP3 discs, “MP3” appears in the
display after the unit reads the file information.
Audio CD
MP3 disc
Track number Playing
time
MP3 file number After the song title is displayed,
the playing time* will appear.
* If the playing time is more than 100 minutes, it appears “--:--” in
the display.
To
Pause playback
Stop playback
Go to the next
track/MP3 file
Go back to the
previous track/
MP3 file
Select a folder on
an MP3 disc
Locate a point
while listening to
the sound
Locate a point
while observing
the display
Remove the CD
Press
ā on the unit (ê on the remote)
Ȱ. To resume play, press it again.
Ą Ȱ.
Ñ ȯ.
à ȯ.
+ to go forward and – to go
backward Ȯ.
Ñ (forward) or à (backward)
ȯ while playing and hold it until
you find the point. (ù or ß ɀ
on the remote)
Ñ (forward) or à (backward)
ȯ in pause and hold it until you
find the point. (ù or ß ɀ on
the remote)
ì PUSH OPEN/CLOSE ȱ.
Tips
ˎ Playback starts from the track/MP3 file you last stopped playing
(Resume play). During stop, the track/MP3 file number to be played
is displayed.
ˎ To cancel the resume play (to start play from the beginning of the
first track/MP3 file), press Ą Ȱ while the CD is stopped. When you
open the CD compartment or turn off the unit, the resume play is
also canceled.
Note
You cannot locate a specific track if “SHUF” or “PGM” is lit in the
display.
Press Ą Ȱ, and then press MODE ȶ repeatedly until “SHUF” and
“PGM” disappear from the display.
Example of folder structure and playing order
The playing order of the folders and files is as follows:
Folder
MP3 file
Notes on MP3 discs
ˎ When the disc is inserted, the unit reads all the files on that disc.
During this time, “READING” is displayed. If there are many folders
or non-MP3 files on the disc, it may take a long time for play to
begin or for the next MP3 file to start play.
We recommend that you do not save unnecessary folders or files
other than MP3 ones in the disc to be used for MP3 listening.
ˎ A folder that does not include an MP3 file is skipped.
ˎ Maximum number of files: 255
Maximum number of folders: 150 (including the root folder)
Maximum number of folders and files in total: 256
Maximum directory levels: 8
ˎ Folder names and file names can be displayed with up to 30
characters including quotation marks.
ˎ The characters A - Z, 0 - 9, and _ can be displayed on this unit.
Other characters are displayed as “_”.
ˎ This unit conforms to Version 1.0, 1.1, 2.2, 2.3 and 2.4 of the ID3 tag
format. When the file has the ID3 tag information, “song title”, “artist
name” and “album name” can be displayed. If the file does not have
the ID3 tag information, “NO TITLE” appears instead of song title,
“NO ARTIST” appears instead of artist name and “NO ALBUM”
appears instead of album name. The ID3 tag information can be
displayed with up to 15 characters.
ˎ When naming, be sure to add the file extension “mp3” to the file
name.
ˎ If you put the extension “mp3” to a file other than an MP3 file, the
unit cannot recognize the file properly and will generate random
noise that could damage your speakers.
ˎ The file name does not correspond to the ID3 tag.
Listening to the radio
1 Press RADIO/BANDˎAUTO PRESET ȭ on the unit
(RADIO/BAND ȭ on the remote) repeatedly.
Each time you press the button, the indication changes
as follows:
“FM” ‚ “AM”
2 Hold down TUNE + or – Ȯ until the frequency
digits begin to change in the display.
The unit automatically scans the radio frequencies and
stops when it finds a clear station.
If you cannot tune in a station, press TUNE + or –
Ȯ repeatedly to change the frequency step by step.
When an FM stereo broadcast is received, “ST”
appears.
Tip
If the FM broadcast is noisy, press MODE ȶ until “Mono” appears in
the display and the radio will play in monaural.
Recording on a tape
Use buttons on the unit for the operation.
1 Press Ąì Ȫ on the unit to open the tape
compartment and insert a blank tape with the side
you want to record on facing upward. Use TYPE I
(normal) tape only. Close the compartment.
2 Select the program source you want to record.
To record from the CD player, press Ą Ȱ on the unit
and place a CD.
To record from the radio, tune in the station you want
(see “Listening to the radio”).
3 Press Ć Ȫ on the unit to start recording (à is
depressed automatically).
To
Pause recording
Stop recording
Press
ê Ȫ on the unit.
Press the button again to
resume recording.
Ąì Ȫ on the unit.
Tips
ˎ Adjusting the volume or the audio emphasis will not affect the
recording level.
ˎ For the best results, use the AC power as a power source for
recording.
ˎ To erase a recording, proceed as follows:
1 Insert the tape whose recording you want to erase.
2 Make sure that “TAPE” is displayed. (If “TAPE” is not displayed,
press à Ȫ on the unit or press FUNCTION Ⱦ on the remote
until it appears in the display.)
3 Press Ć Ȫ on the unit.
Playing a tape
Use buttons on the unit for the operation.
1 Press Ąì Ȫ on the unit, and insert the tape into
the tape compartment with the side you want to
play facing upward. Use TYPE I (normal) tape only.
Close the compartment.
Make sure there is no slack in the tape to avoid
damaging the tape or the unit.
2 Press à Ȫ on the unit.
The unit starts playing.
To
Pause playback
Stop playback
Fast-forward or
rewind*
Eject the cassette
Press
ê Ȫ on the unit. To resume play,
press it again.
Ąì Ȫ on the unit.
ù or ß (rewind or fast
forward) Ȫ on the unit.
Ąì Ȫ on the unit.
* When the tape is wound to the end, press Ąì Ȫ to release ù or
ß Ȫ.
5

5 Page





CFD-G770CP arduino
CFD-G700CP/G770CP/G770CPK
SECTION 3
DISASSEMBLY
www.DataSheet4U.com
3-1. DISASSEMBLY FLOW
• This set can be disassembled in the order shown below.
SET
3-2. CABINET (UPPER) (1) SECTION
(Page 12)
3-3. CABINET (UPPER) (2) SECTION
(Page 12)
3-4. CABINET (FRONT)
SECTION
(Page 13)
3-11. WOOFER KEY BOARD,
CD KEY BOARD
(Page 17)
3-12. TUNER BOARD
(Page 17)
3-14. MAIN BOARD
(Page 18)
3-6. FRONT PANEL
(Page 14)
3-17. TC BOARD
(Page 20)
3-13. TAPE MECHANISM
DECK
(Page 18)
3-18. MAIN BELT,
SUB BELT
(Page 20)
3-15. CD BLOCK
SECTION
(Page 19)
3-16. OPTICAL PICK-UP
(KSM-213CDP/C2NP)
(Page 19)
3-7. LED BOARD
(Page 14)
3-8. SPEAKER (13cm)
(Page 15)
3-5. LCD BOARD,
AUDIO IN BOARD,
HEADPHONE BOARD,
POWER KEY BOARD,
MICROPHONE BOARD (CFD-G770CPK),
VOLUME KEY BOARD
(Page 13)
3-9. SPEAKER (10cm)
(Page 15)
3-10. POWER BOARD,
BATTERY BOARD,
D-LIGHT BOARD (CFD-G700CP)
(Page 16)
11

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet CFD-G770CP.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
CFD-G770CPCD RADIO CASSETTE-CORDERSony
Sony
CFD-G770CPKCD RADIO CASSETTE-CORDERSony
Sony

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar