DataSheet.es    


PDF UCLAMP0501T Data sheet ( Hoja de datos )

Número de pieza UCLAMP0501T
Descripción 1-Line ESD protection
Fabricantes Semtech Corporation 
Logotipo Semtech Corporation Logotipo



Hay una vista previa y un enlace de descarga de UCLAMP0501T (archivo pdf) en la parte inferior de esta página.


Total 8 Páginas

No Preview Available ! UCLAMP0501T Hoja de datos, Descripción, Manual

PROTECTION PRODUCTS - MicroClampTM
Description
The μClampTM series of TVS arrays are designed to pro-
tect sensitive electronics from damage or latch-up due
to ESD. It is designed to replace multilayer varistors
(MLVs) in portable applications such as cell phones, note-
book computers, and other portable electronics. It fea-
tures large cross-sectional area junctions for conducting
high transient currents. They offer desirable character-
istics for board level protection including fast response
time, low operating and clamping voltage, and no device
degradation.
The μClampTM0501T is in a 2-pin, RoHS/WEEE compli-
ant, SLP1006P2T package. It measures 1.0 x 0.6 mm
with a nominal height of only 0.4mm. The leads are
spaced at a pitch of 0.65mm and are finished with
lead-free NiPdAu. Each device will protect one line
operating at 5 volts. It gives the designer the flexibility
to protect single lines in applications where arrays are
not practical. They may be used to meet the ESD
immunity requirements of IEC 61000-4-2, Level 4
(±15kV air, ±8kV contact discharge). The combination
of small size and high ESD surge capability makes
them ideal for use in portable applications such as
cellular phones, digital cameras, and MP3 players.
uClamp0501T
Low Profile μClampTM
1-Line EwwSwD.DatpaSrheoett4eU.ccotmion
Features
‹ Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
Cable Discharge Event (CDE)
‹ Ultra-small package (1.0 x 0.6 x 0.4mm)
‹ Protects one data line
‹ Low clamping voltage
‹ Working voltage: 5V
‹ Low leakage current
‹ Solid-state silicon-avalanche technology
Mechanical Characteristics
‹ SLP1006P2T package
‹ RoHS/WEEE Compliant
‹ Nominal Dimensions: 1.0 x 0.6 x 0.4 mm
‹ Lead Finish: NiPdAu
‹ Molding compound flammability rating: UL 94V-0
‹ Marking : Marking code, cathode band
‹ Packaging : Tape and Reel
Applications
‹ Cellular Handsets & Accessories
‹ Personal Digital Assistants (PDAs)
‹ Notebooks & Handhelds
‹ Portable Instrumentation
‹ Digital Cameras
‹ Peripherals
‹ MP3 Players
Dimensions
Schematic & PIN Configuration
1.0
0.65
0.60
0.40
Nominal Dimensions (mm)
Revision 07/31/2007
SLP1006P2T (Bottom View)
1 www.semtech.com

1 page




UCLAMP0501T pdf
PROTECTION PRODUCTS
Applications Information
Device Connection Options
This device is designed to protect one data or power
supply line. The device is unidirectional and may be
used on lines where the signal polarity is above ground.
The cathode band should be placed towards the line
that is to be protected.
Circuit Board Layout Recommendations for Suppres-
sion of ESD.
Good circuit board layout is critical for the suppression
of ESD induced transients. The following guidelines are
recommended:
z Place the TVS near the input terminals or connec-
tors to restrict transient coupling.
z Minimize the path length between the TVS and the
protected line.
z Minimize all conductive loops including power and
ground loops.
z The ESD transient return path to ground should be
kept as short as possible.
z Never run critical signals near board edges.
z Use ground planes whenever possible.
uClamp0501T
www.DataSheet4U.com
Circuit Diagram
© 2007 Semtech Corp.
5
www.semtech.com

5 Page










PáginasTotal 8 Páginas
PDF Descargar[ Datasheet UCLAMP0501T.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
UCLAMP0501H1-Line ESD protectionSemtech Corporation
Semtech Corporation
UCLAMP0501P1-Line ESD protectionSemtech Corporation
Semtech Corporation
UCLAMP0501T1-Line ESD protectionSemtech Corporation
Semtech Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar