DataSheet.es    


PDF CAT5261 Data sheet ( Hoja de datos )

Número de pieza CAT5261
Descripción Dual Digitally Programmable Potentiometers
Fabricantes Catalyst Semiconductor 
Logotipo Catalyst Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de CAT5261 (archivo pdf) en la parte inferior de esta página.


Total 15 Páginas

No Preview Available ! CAT5261 Hoja de datos, Descripción, Manual

CAT5261www.DataSheet4U.com
Dual Digitally Programmable Potentiometers
(DPP™) with 256 Taps and SPI Interface
FEATURES
„ Two linear-taper digitally programmable
potentiometers
„ 256 resistor taps per potentiometer
„ End to end resistance 50kor 100k
„ Potentiometer control and memory access via
SPI interface
„ Low wiper resistance, typically 100
„ Nonvolatile memory storage for up to four
wiper settings for each potentiometer
„ Automatic recall of saved wiper settings at
power up
„ 2.5 to 6.0 volt operation
„ Standby current less than 1µA
„ 1,000,000 nonvolatile WRITE cycles
„ 100 year nonvolatile memory data retention
„ 24-lead SOIC and 24-lead TSSOP
„ Industrial temperature range
„ Industrial temperature range
For Ordering Information details, see page 14.
DESCRIPTION
The CAT5261 is two Digitally Programmable
Potentiometers (DPPs™) integrated with control logic
and 8 bytes of NVRAM memory. Each DPP consists of
a series of resistive elements connected between two
externally accessible end points. The tap points
between each resistive element are connected to the
wiper outputs with CMOS switches. A separate 8-bit
control register (WCR) independently controls the wiper
tap switches for each DPP. Associated with each wiper
control register are four 8-bit non-volatile memory data
registers (DR) used for storing up to four wiper settings.
Writing to the wiper control register or any of the non-
volatile data registers is via a SPI serial bus. On power-
up, the contents of the first data register (DR0) for each
of the potentiometers is automatically loaded into its
respective wiper control register.
The CAT5261 can be used as a potentiometer or as a
two terminal, variable resistor. It is intended for circuit
level or system level adjustments in a wide variety of
applications. It is available in the -40°C to 85°C
industrial operating temperature range and offered in
a 24-lead SOIC and TSSOP package.
PIN CONFIGURATION
SOIC/TSSOP (W, Y)
SO 1
24 H¯¯O¯L¯D¯
A0 2
23 SCK
NC 3
22 NC
NC 4
21 NC
NC 5
20 NC
NC
6
CAT
5261
19
NC
VCC 7
18 GND
RL0 8
17 RW1
RH0 9
16 RH1
RW0 10
¯C¯S¯ 11
15 RL1
14 A1
¯W¯P¯ 12
13 SI
FUNCTIONAL DIAGRAM
CS
SCK
SI
SO
SPI BUS
INTERFACE
WIPER
CONTROL
REGISTERS
RH0 RH1
WP
A0
A1
HOLD
CONTROL
LOGIC
NONVOLATILE
DATA
REGISTERS
RL0 RL1
RW0
RW1
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
1
Doc. No. MD-2122 Rev. E

1 page




CAT5261 pdf
CAT5261
www.DataSheet4U.com
D.C. OPERATING CHARACTERISTICS
VCC = +2.5V to +6.0V, unless otherwise specified.
Symbol Parameter
Test Conditions
Min
ICC1 Power Supply Current
ICC2
Power Supply Current
Non-volatile WRITE
fSCL = 400kHz, SDA = Open
VCC = 6V, Inputs = GNDs
fSCK = 400kHz, SDA Open
VCC = 6V, Input = GND
ISB Standby Current (VCC = 5.0V) VIN = GND or VCC, SDA = Open
ILI Input Leakage Current
VIN = GND to VCC
ILO Output Leakage Current
VOUT = GND to VCC
VIL Input Low Voltage
-1
VIH Input High Voltage
VCC x 0.7
VOL1 Output Low Voltage (VCC = 3.0V) IOL = 3mA
VOH1 Output High Voltage
IOH = -1.6mA
VCC – 0.8
PIN CAPACITANCE(1)
TA = 25ºC, f = 1.0MHz, VCC = 5V, unless otherwise specified.
Symbol Test
Conditions
COUT(1)
CIN(1)
Output Capacitance (SO)
Input Capacitance (¯C¯S¯, SCK, SI, ¯W¯P¯,H¯¯O¯L¯D¯, A0, A1)
VOUT = 0V
VIN = 0V
A.C. CHARACTERISTICS
Symbol Parameter
Test Conditions
Min
tSU Data Setup Time
tH Data Hold Time
tWH SCK High Time
tWL SCK Low Time
fSCK Clock Frequency
tLZ H¯¯O¯L¯D¯ to Output Low Z
tRI(1) Input Rise Time
tFI(1) Input Fall Time
tHD H¯¯O¯L¯D¯ Setup Time
tCD H¯¯O¯L¯D¯ Hold Time
tV Output Valid from Clock Low
tHO Output Hold Time
tDIS Output Disable Time
tHZ H¯¯O¯L¯D¯ to Output High Z
tCS ¯C¯S¯ High Time
tCSS ¯C¯S¯ Setup Time
tCSH ¯C¯S¯ Hold Time
CL = 50pF
50
50
125
125
DC
100
100
0
2
250
250
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
Max
1
5
1
10
10
VCC x 0.3
VCC + 1.0
0.4
Max
8
6
Max
3
50
2
2
200
250
100
Units
mA
mA
µA
µA
µA
V
V
V
V
Units
pF
pF
Units
ns
ns
ns
ns
MHz
ns
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
5
Doc. No. MD-2122 Rev. E

5 Page





CAT5261 arduino
Global Transfer Data Register (DR) to Wiper Control Register (WCR)
DEVICE ADDRESSES
INSTRUCTION
¯C¯S¯ 0 1 0 1 0 0 A A 0 0 0 1 R R 0 0 ¯C¯S¯
10
10
CAT5261
www.DataSheet4U.com
Global Transfer Wiper Control Register (WCR) to Data Register (DR)
DEVICE ADDRESSES
¯C¯S¯ 0 1 0 1 0 0 A A
10
INSTRUCTION
1 0 0 0RR 0
10
0
¯C¯S¯
High Voltage
Write Cycle
Transfer Wiper Control Register (WCR) to Data Register (DR)
DEVICE ADDRESSES
INSTRUCTION
¯C¯S¯ 0 1 0 1 0
0
A
1
A
0
1110RR
10
P
1
P
0
¯C¯S¯
High Voltage
Write Cycle
Transfer Data Register (DR) to Wiper Control Register (WCR)
DEVICE ADDRESSES
INSTRUCTION
¯C¯S¯ 0 1 0 1 0 0 A A 1 1 0 1 R R P P ¯C¯S¯
10
10 1 0
Increment (I)/Decrement (D) Wiper Control Register (WCR)
DEVICE ADDRESSES
INSTRUCTION
¯C¯S¯ 0 1 0 1 0
0
A
1
A
0
00100
0 P P I/D I/D
10
DATA
...
I/D I/D ¯C¯S¯
Notes:
(1) Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after a STOP has been issued.
© Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
11
Doc. No. MD-2122 Rev. E

11 Page







PáginasTotal 15 Páginas
PDF Descargar[ Datasheet CAT5261.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
CAT5261Dual Digital PotentiometerON Semiconductor
ON Semiconductor
CAT5261Dual Digitally Programmable PotentiometersCatalyst Semiconductor
Catalyst Semiconductor
CAT5269Dual Digital PotentiometerON Semiconductor
ON Semiconductor
CAT5269Dual Digitally Programmable PotentiometersCatalyst Semiconductor
Catalyst Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar