G084SN05-V3 Hoja de datos PDF

PDF G084SN05-V3 Datasheet ( Hoja de datos )

Número de pieza G084SN05-V3
Descripción Color TFT-LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo
Vista previa
Total 25 Páginas
G084SN05-V3 datasheet

1 Page

G084SN05-V3 pdf
1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnection from input
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a module has to be put back into the packing container slot after once it
was taken out from the container, do not press the center of the CCFL Reflector
edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise
the TFT module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the interface Connector of the TFT module.
11) After installation of the TFT module into an enclosure, do not twist nor bend the
TFT module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from
outside. Otherwise the TFT module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD
module should be supplied by power complied with requirements of Limited Power
Source, or be applied exemption.
14) The LCD module is designed so that the CFL in it is supplied by Limited Current
Circuit. Do not connect the CFL in Hazardous Voltage Circuit.
G084SN05 V.3 ver.0.1

5 Page

G084SN05-V3 arduino
Note 1: Definition of white uniformity:
White uniformity is calculated with the following formula.
Luminance are measured at the following nine points (1~9).
δW =
Maximum Brightness of nine points
Minimum Brightness of nine points
G084SN05 V.3 ver.0.1

10 Page

PáginasTotal 25 Páginas
PDF Descargar[ G084SN05-V3.PDF ]

Enlace url

Hoja de datos destacado

Número de piezaDescripciónFabricantes
G084SN05-V0LCD ModuleAUO
G084SN05-V1LCD ModuleAUO
G084SN05-V2Color TFT-LCD ModuleAUO
G084SN05-V3Color TFT-LCD ModuleAUO
G084SN05-V4SVGA Color TFT-LCD ModuleAUO
G084SN05-V7Color TFT-LCD ModuleAUO
G084SN05-V8LCD ModuleAUO

Número de piezaDescripciónFabricantes

Low Power Audio Codec.

Analog Devices
Analog Devices

32.768 kHz and MHz GreenCLK.


High Voltage 3 phase Motor Driver IC.


12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

Index : 0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z    |   2018   |  Contacto  |  Buscar