DataSheet.es    


PDF F981A225MMA Data sheet ( Hoja de datos )

Número de pieza F981A225MMA
Descripción SOLID TANTALUM ELECTROLYTIC CAPACITORS
Fabricantes Nichicon corporation 
Logotipo Nichicon corporation Logotipo



Hay una vista previa y un enlace de descarga de F981A225MMA (archivo pdf) en la parte inferior de esta página.


Total 1 Páginas

No Preview Available ! F981A225MMA Hoja de datos, Descripción, Manual

SOLID TANTALUM ELECTROLYTIC CAPACITORS
F98 Resin-molded Chip,
High Capacitance Series
Adapted to the RoHS directive (2002/95/EC).
Specifications
Type numbering system (Example : 6.3V 10 µF)
123
F98
45
0J
678
106
9 10 11
MM
Taping code
(Refer to page 267 for details)
Case code
Capacitance tolerance
Rated Capacitance Rated voltage
Series
Drawing
L W1
H
W2
S1 S2 S1
(mm)
Cace Code L W1 W2 H S1 S2
M 1.6 ± 0.1 0.85 ± 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 0.6 ± 0.1
S 2.0 ± 0.1 1.25 ± 0.1 0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 1.0 ± 0.1
Marking
www.DataSheet4U.com
J
Item
Performance Characteristics
Category
Temperature Range
--55 ~ +125°C (Rated temperature : 85°C)
Capacitance Tolerance ±20% (at 120Hz)
Dissipation Factor(120Hz) Refer to the list below (* 1)
ESR(100kHz)
Refer to the list below (* 1)
Leakage Current
After 5 minute's application of rated voltage, leakage current at
20°C is not more than 0.1CV or 0.5µA, whichever is greater.
Damp Heat
At 40°C, 90 ~ 95% R.H., For 500hours (No voltage applied)
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Temperature Cycles
At --55°C / +125°C, For 30 minutes each, 5 cycles
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
Initial specified value or less
Resistance to Soldering
Heat
At 260°C, For 10 seconds, Reflow,
Capacitance Change Refor to the list below (* 1)
Leakage Current
Initial specified value or less
Leakage Current
Initial specified value or less
Surge
After application of surge in series with a 1kresistor at the
rate of 30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 85°C, capacitors meet the characteristics
requirements listed below.
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Endurance
After 1000 hours' application of rated voltage in series with a
3resistor at 85°C, capacitors meet the characteristic
requirements listed below
Capacitance Change Refor to the list below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Shear Test
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
5N (0.51kg f)
For 10 ± 1seconds
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor, the
pressure strength is applied with
a specified jig at the center of the R230
substrate so that the substrate
20
may bend by 1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
45 45
capacitor terminals.
Rated voltage
(Voltage code)
As for the surge and derated voltage at 125˚C, refer to page 266 for details.
Standard ratings
Rated Volt
(V)
Rated
Capacitance
(µF)
Case
code
Part Number
Leakage
Current
(µA)
Disspation
Factor
ESR *1C/C
(%@120Hz) (@100kHz) (%)
V 2.5 4 6.3 10 16 20
Cap.(µF)
Code
0E
0G
0J
1A
1C
1D
1 105
MM
2.2 225
MM
4.7 475
MMM
10 106
MM S
22 226
MM S
2.5 47 M F980E476MMA 1.2
22 M F980G226MMA 0.9
4 33 M F980G336MMA 1.3
68 S F980G686MSA 2.7
4.7 M F980J475MMA 0.5
10 M F980J106MMA 0.6
6.3 22 M F980J226MMA 1.4
30
15
30
30
20
8
20
4 ± 30
7.5 ± 30
4 ± 30
4 ± 30
7.5 ± 30
6 ± 30
6 ± 30
33 336
M (M) S
47 S F980J476MSA 3.0
25
6 ± 30
47 476 M (M) S
2.2 M F981A225MMA 0.5
6
7.5 ± 30
68 686
S
4.7 M F981A475MMA 0.5
6
6 ± 30
100 107 (S)
(S)
10 10 M F981A106MMA 1.0 20
7.5 ± 30
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
22 S F981A226MSA 2.2
33 S F981A336MSA 3.3
1 M F981C105MMA 0.5
20
30
6
4 ± 20
6 ± 30
10 ± 30
16 2.2 M F981C225MMA 0.5
4.7 M F981C475MMA 0.8
6
12
10 ± 30
12 ± 30
10 S F981C106MSA 1.6
18
4 ± 20
20 1 M F981D105MMA 0.5 6
10 ± 30
CAT.8100V

1 page





PáginasTotal 1 Páginas
PDF Descargar[ Datasheet F981A225MMA.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
F981A225MMASOLID TANTALUM ELECTROLYTIC CAPACITORSNichicon corporation
Nichicon corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar