|
|
Número de pieza | SA7527 | |
Descripción | POWER FACTOR CORRECTION CONTROLLER | |
Fabricantes | Silan Microelectronics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SA7527 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
No Preview Available ! SA7527
POWER FACTOR CORRECTION CONTROLLER OF CRITICAL DUCTING
DESCRIPTION
The SA7527 provides simple and high performance active power
factor correction. The SA7527 is optimized for electronic ballasts and
low power and high-density power supplies which require minimum
board size, reduced external components and low power dissipation.
Because the R/C filter is included in the current sense block, the
external R/C filter is not necessary. Special circuitry has also been
added to prevent no load runaway conditions. Regardless of the supply
voltage, the output drive clamping circuit limits the overshoot of the
power MOSFET gate drive. It greatly enhances the system reliability.
DIP-8-300-2.54
SOP-8-225-1.27
FEATURES
* Internal start-up timer
* Internal R/C filter eliminates the need for an external R/C filter
* Very precise adjustable output over voltage protection
* Zero current detector
* One quadrant multiplier
* Trimmed 1.5% internal band gap reference
* Under voltage lockout with 3V of hysteresis
* Totem pole output with high state clamp
* Low start-up and operating current
* 8-pin DIP or 8-pin SOP
ORDERING INFORMATION
Device
SA7527
SA7527S
Package
DIP-8-300-2.54
SOP-8-225-1.27
APPLICATIONS
* Electronic ballast
* SMPS
BLOCK DIAGRAM
www.DataSheet4U.com
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http: www.silan.com.cn
REV:1.0 2005.07.22
Page 1 of 8
1 page (Continued)
Figure 3. Supply Current vs Supply Voltage
0.015
0.012
0.009
0.006
0.003
0.000
0
10 20 30
40
Supply Voltage (V)
50
TEST CIRCUIT
SA7527
TEST SPECIFICATION (Unless otherwise specified, VDC2=14V)
Parameter
Switches
Test conditions
Vth(st)
www.DataSheet4U.com
HY(st)
S2,S3,S4,S5
S2,S3,S4,S5
VDC3=3,VDC4=1,VDC6=0
VDC3=3,VDC4=1,VDC6=0
I(st)
I(cc)
Icc(ovp)
S2,S3,S4,S5
S2,S3,S4,S5
S1
VDC3=3,VDC4=1,VDC6=0
VDC3=3,VDC4=1,VDC6=0
VDC1=3
Idcc S1,S3,S4,S7,S8 VDC6=0
Vref
Vref
Ib(ea)
I(source)
I(sink)
Veao(H)
Veao(L)
Ib(m)
S9
S9
S1
S1,S2
S1,S2
S1
S1
S3
--
--
VDC1 change
VDC1=0,VDC3=4
VDC1=3,VDC3=4
VDC1=0
VDC1=3
--
Test
point
B
B
B
B
B
B
G
G
G
A
A
A
A
E
Remark
VDC2 increase
Following above, decrease the
VDC2 until C level changed
VDC2= Vth(st)-0.2
--
--
Input 50kHz/2V square wave to
F
VDC2=14V 25V
--
--
--
The source current of A is 1mA
The sink current of A is 1mA
VDC4: 0~4V
(To be continued)
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http: www.silan.com.cn
REV:1.0 2005.07.22
Page 5 of 8
5 Page |
Páginas | Total 8 Páginas | |
PDF Descargar | [ Datasheet SA7527.PDF ] |
Número de pieza | Descripción | Fabricantes |
SA7527 | POWER FACTOR CORRECTION CONTROLLER | Silan Microelectronics |
SA7527S | POWER FACTOR CORRECTION CONTROLLER | Silan Microelectronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |