|
|
Número de pieza | FAN6961 | |
Descripción | Boundary Mode PFC Controller | |
Fabricantes | Fairchild Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de FAN6961 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
No Preview Available ! January 2009
FAN6961
Boundary Mode PFC Controller
Features
Boundary Mode PFC Controller
Low Input Current THD
Controlled On-Time PWM
Zero-Current Detection
Cycle-by-Cycle Current Limiting
Leading-Edge Blanking instead of RC Filtering
Low Start-up Current: 10µA Typical
Low Operating Current: 4.5mA Typical
Feedback Open-Loop Protection
Programmable Maximum On-Time (MOT)
Output Over-Voltage Clamping Protection
Clamped Gate Output Voltage 16.5V
Applications
Electric Lamp Ballasts
AC-DC Switching Mode Power Converter
www.DataSheet4OU.pceonmFrame Power Supplies and Power Adapters
Flyback Power Converters with ZCS / ZVS
Description
The FAN6961 is an 8-pin, boundary-mode, PFC
controller IC intended for controlling PFC pre-
regulators. The FAN6961 provides a controlled on-time
to regulate the output DC voltage and achieve natural
power factor correction. The maximum on-time of the
external switch is programmable to ensure safe
operation during AC brownouts. An innovative multi-
vector error amplifier is built in to provide rapid transient
response and precise output voltage clamping. A built-
in circuit disables the controller if the output feedback
loop is opened. The start-up current is lower than 20µA
and the operating current has been reduced to under
6mA. The supply voltage can be up to 25V, maximizing
application flexibility.
Ordering Information
Part
Number
FAN6961SZ
FAN6961DZ
FAN6961SY
Operating
Temperature Range
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
Package
8-Pin, Small Outline Package (SOP)
8-Pin, Dual In-line Package (DIP)
8-Pin, Small Outline Package (SOP)
Eco Status
RoHS
RoHS
Green
Packing
Method
Tape & Reel
Tube
Tape & Reel
For Fairchild’s definition of “green” Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html.
© 2008 Fairchild Semiconductor Corporation
FAN6961 • Rev. 1.0.2
www.fairchildsemi.com
1 page Electrical Characteristics
VCC=15V and TA=25°C unless otherwise noted.
Symbol
Parameter
VCC Section
VCC-OP Continuous Operation Voltage
VCC-ON Turn-on Threshold Voltage
VCC-OFF Turn-off Threshold Voltage
ICC-ST Start-up Current
ICC-OP Operating Supply Current
VCC-OVP VDD Over-Voltage Protection Level
tD-VCCOVP VDD Over-Voltage Protection Debounce
Error Amplifier Section
VREF
Gm
Reference Voltage
Transconductance
VINVH Clamp High Feedback Voltage
VINVL Clamp Low Feedback Voltage
VOUT HIGH Output High Voltage
VOZ Zero Duty Cycle Output Voltage
VINV-OVP Over Voltage Protection for INV Input
VINV-UVP Under Voltage Protection for INV Input
Source Current
ICOMP
Sink Current
www.DataShCeuert4rUen.cto-mSense Section
VPK
Threshold Voltage for Peak Current Limit
Cycle-by-Cycle Limit
tPD Propagation Delay
tLEB Leading-Edge Blanking Time
Gate Section
VZ-OUT Output Voltage Maximum (Clamp)
VOL Output Voltage Low
VOH Output Voltage High
tR Rising Time
tF Falling Time
Conditions
Min. Typ. Max. Units
VCC=VCC-ON – 0.16V
VCC=12V, VCS=0V,
CL=3nF, fSW=60KHz
24.5
11 12 13
8.5 9.5 10.5
10 20
4.5 6
26.5 27.5 28.5
30
V
V
V
µA
mA
V
µs
VINV=2.35V, VCOMP=1.5V
VINV=1.5V,
VINV=2.65V, VCOMP=5V
2.475
2.25
4.8
1.15
2.70
0.40
10
550
10
2.500
125
2.65
2.30
1.25
2.75
0.45
20
800
20
2.525
2.70
1.35
2.80
0.50
V
μmho
V
V
V
V
V
V
μA
RMOT=24kΩ, VCOMP=5V
RMOT=24kΩ,
VCOMP=VOZ+50mV
0.77 0.82 0.87
200
400 500
270 350
V
ns
ns
VCC=25V
VCC=15V, IO=100mA
VCC=14V, IO=100mA
VCC=12V, CL=3nF,
20~80%
VCC=12V, CL=3nF,
80~20%
15.0 16.5 18.0
1.4
8
80
V
V
V
ns
40 ns
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN6961 • Rev. 1.0.2
5
www.fairchildsemi.com
5 Page Physical Dimensions
9.83
9.00
6.67
6.096
5.08 MAX
3.683
3.20
8.255
7.61
7.62
0.33 MIN
(0.56)
2.54
3.60
3.00
0.56
0.355
1.65
1.27
7.62
0.356
0.20
9.957
7.87
NOTES: UNLESS OTHERWISE SPECIFIED
www.DataSheet4U.comA) THIS PACKAGE CONFORMS TO
JEDEC MS-001 VARIATION BA
B) ALL DIMENSIONS ARE IN MILLIMETERS.
C) DIMENSIONS ARE EXCLUSIVE OF BURRS,
MOLD FLASH, AND TIE BAR EXTRUSIONS.
D) DIMENSIONS AND TOLERANCES PER
ASME Y14.5M-1994
E) DRAWING FILENAME AND REVSION: MKT-N08FREV2.
Figure 15. 8-Lead, PDIP, JEDEC MS-001, .300 Inch Wide
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify
or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions,
specifically the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2008 Fairchild Semiconductor Corporation
FAN6961 • Rev. 1.0.2
11
www.fairchildsemi.com
11 Page |
Páginas | Total 13 Páginas | |
PDF Descargar | [ Datasheet FAN6961.PDF ] |
Número de pieza | Descripción | Fabricantes |
FAN6961 | Boundary Mode PFC Controller | Fairchild Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |