DataSheet.es    

PDF V-165-xxx Datasheet ( Hoja de datos )

Número de pieza V-165-xxx
Descripción Miniature Basci Switch
Fabricantes Omron 
Logotipo Omron Logotipo

Total 27 Páginas
		
V-165-xxx Hoja de datos, Descripción, Manual
www.DataSheet4U.com
Miniature Basic Switch
Reliable Basic Switches in a Wide
Variation
Wide variation of best-selling microswitches with
switching currents of 10 to 21 A.
Can be used for interrupting current when doors are
opened or closed.
Available in two types of cases:
thermoplastic resin and thermosetting resin.
V
Ordering Information
Model Number Legend
V-jjj-jjjj-j
123 4567 8
1. Ratings
21: 21 A at 250 VAC
16: 16 A at 250 VAC
15: 15 A at 250 VAC
11: 11 A at 250 VAC
10: 10 A at 250 VAC
2. Contact Gap
None: 1 mm (F gap)
G: 0.5 mm (G gap) (for remodelling)
3. Actuator
None: Pin plunger
1: Short hinge lever
2: Hinge lever
3: Long hinge lever
4: Simulated roller lever
5: Short hinge roller lever
6: Hinge roller lever
4. Contact Form
1: SPDT (COM bottom terminal, double-throw)
2: SPST-NC (COM bottom terminal, normally closed)
3: SPST-NO (COM bottom terminal, normally open)
4: SPDT (COM side terminal, double-throw)
5: SPST-NC (COM side terminal, normally closed)
6: SPST-NO (COM side terminal, normally open)
RCEW
5. Terminals
A: Solder terminals
C2: Quick-connect terminals (#187)
C: Quick-connect terminals (#250)
B: Screw terminals
6. Barrier (Models with Thermoplastic Case Only)
None: Without barrier
R: Right-hand barrier
L: Left-hand barrier
7. Maximum Operating Force
6: 3.92 N {400 gf}
5: 1.96 N {200 gf}
4: 0.98 N {100 gf}
Note: These values are for the pin plunger models.
8. Special Purpose (Models with Thermosetting Case
Only)
T: Heat-resistive
110

1 page

V-165-xxx pdf
VV
www.DTahtearSmhoeseet4ttUin.cgoCmase
Actuator
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
COM
terminal
position
Bottom
Side
Bottom
Contact
form
SPDT
SPST-NC
SPST-NO
SPDT
SPST-NC
SPST-NO
SPDT
Terminals
(see note
1)
A
C2
B
A
C2
B
A
C2
B
A
A
C2
B
A
C2
B
A
C2
Simulated roller lever
B
A
15 A
OF: 1.96 N {200 gf}
V-15-1A5
V-15-1C25
V-15-1B5
V-15-2A5
V-15-2C25
V-15-2B5
V-15-3A5
V-15-3C25
V-15-3B5
V-15-4A5
V-15-5A5
V-15-6A5
V-151-1A5
V-151-1C25
V-151-1B5
V-152-1A5
V-152-1C25
V-152-1B5
V-153-1A5
V-153-1C25
V-153-1B5
V-154-1A5
10 A
OF: 1.96 N {200 gf} OF: 0.98 N {100 gf}
V-10-1A5
V-10-1C25
V-10-1B5
V-10-2A5
V-10-2C25
V-10-2B5
V-10-3A5
V-10-3C25
V-10-3B5
V-10-4A5
V-10-5A5
V-10-6A5
V-101-1A5
V-101-1C25
V-101-1B5
V-102-1A5
V-102-1C25
V-102-1B5
V-103-1A5
V-10-1A4
V-10-1C24
V-10-1B4
V-10-2A4
V-10-2C24
V-10-2B4
V-10-3A4
V-10-3C24
V-10-3B4
V-10-4A4
V-10-5A4
V-10-6A4
V-101-1A4
V-101-1C24
V-101-1B4
V-102-1A4
V-102-1C24
V-102-1B4
V-103-1A4
V-103-1C25
V-103-1C24
V-103-1B5
V-104-1A5
V-103-1B4
V-104-1A4
C2 V-154-1C25
V-104-1C25
V-104-1C24
Short hinge
roller lever
B V-154-1B5
A V-155-1A5
C2 V-155-1C25
V-104-1B5
V-105-1A5
V-105-1C25
V-104-1B4
V-105-1A4
V-105-1C24
Hinge roller lever
B V-155-1B5
A V-156-1A5
C2 V-156-1C25
B V-156-1B5
Note: 1. A: Solder terminals
C2: Quick-connect terminals (#187)
B: Screw terminals
2. OF values shown in the table are for the pin plunger models.
V-105-1B5
V-106-1A5
V-106-1C25
V-106-1B5
V-105-1B4
V-106-1A4
V-106-1C24
V-106-1B4
114

5 Page

V-165-xxx arduino
VV
www.DatDaSihmeeet4nU.scoiomns and Operating Characteristics
Note: 1. All units are in millimeters unless otherwise indicated.
2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
3. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models with a switching current of
16 A or 11 A incorporates terminals A and C2. These models are different from #250 models in terminal size only. Terminals A, C2,
and side common terminals are omitted from the following drawings. Refer to Kinds of Terminals on page 119 for these terminals.
4. The j in the model number is for the terminal code.
5. The operating characteristics are for operation in the A direction ( ).
Pin Plunger Models
(Without Barrier)
PT
V-21-1j6
2.8
V-16-1j5
V-11-1j4
2.8
OP
10.3±0.1
3.1
+0.13
–0.03
3.4±0.15 dia.
A 20.2±0.25
1.6
3.1
+0.13
–0.03
dia.
holes
2.8
0.6
8.4
15.9 19.1
22.2±0.1 2.8 (12.0)
27.8
39.8±0.8
t=0.8
Three, quick-connect
terminals (#250)
4.2
10.3
2.8
(With Right-hand Barrier)
V-21-1jR6
V-16-1jR5
PT 2.8
2.8
OP
10.3±0.1
3.1
+0.13
–0.03
3.4±0.15 dia.
A 20.2±0.25
1.6
3.1
+0.13
–0.03
dia.
holes
2.8
0.6
8.4 19.1
15.9
21.9
t=0.8
22.2±0.1 2.8
(12.0)
Three, quick-connect
terminals (#250)
27.8
39.8±0.8
40.2
4.2
10.3
2.8
0.6
Model
OF max.
RF min.
PT max.
OT min.
MD max.
OP
V-21-1j6
3.92 N {400 gf}
0.78 N {80 gf}
1.2 mm
1.0 mm
0.4 mm
14.7±0.4 mm
V-16-1j5
1.96 N {200 gf}
0.49 N {50 gf}
(With Left-hand Barrier)
V-21-1jL6
V-16-1jL5
4.2
2.8
0.6
10.3
3.1
+0.13
–0.03
dia.
holes
20.2±0.25
A
1.6
0.6 2.8
2.8 2.8 PT
19.1 8.4
21.9
15.9
t=0.8
Three, quick-connect
terminals (#250)
(12.0) 2.8 22.2±0.1
27.8
39.8±0.8
10.3±0.1 OP
3.1
+0.13
–0.03
3.4±0.15 dia.
40.2
Model
OF max.
RF min.
PT max.
OT min.
MD max.
OP
V-11-1j4
0.98 N {100 gf}
0.20 N {20 gf}
1.2 mm
1.0 mm
0.4 mm
14.7±0.4 mm
V-11-1j5
1.96 N {200 gf}
0.49 N {50 gf}
120

11 Page


PáginasTotal 27 Páginas
PDF Descargar[ V-165-xxx.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
V-165-xxxMiniature Basci SwitchOmron
Omron

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2018   |  Privacy Policy  |  Contacto  |  Buscar