DataSheet.es    


PDF GS9092 Data sheet ( Hoja de datos )

Número de pieza GS9092
Descripción GenLINX-R III 270Mb/s Serializer
Fabricantes Gennum Corporation 
Logotipo Gennum Corporation Logotipo



Hay una vista previa y un enlace de descarga de GS9092 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! GS9092 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
Key Features
• SMPTE 259M-C compliant scrambling and NRZI to
NRZ encoding (with bypass)
• DVB-ASI sync word insertion and 8b/10b encoding
• Integrated Cable Driver
• Integrated line-based FIFO for data
alignment/delay, clock phase interchange, DVB-ASI
data packet insertion, and ancillary data packet
insertion
• User selectable additional processing features
including:
• ANC data checksum, and line number
calculation and insertion
• TRS and EDH packet generation and insertion
• illegal code remapping
• Enhanced Gennum Serial Peripheral Interface
(GSPI)
• JTAG test interface
• +1.8V internal cable driver and core power supply
• Optional +1.8V or +3.3V digital I/O power supply
• Small footprint (8mm x 8mm)
• Low power operation (typically 170mW)
• Pb-free and RoHS compliant
Applications
• SMPTE 259M-C Serial Digital Interfaces
• DVB-ASI Serial Digital Interfaces
GS9092 GenLINX® III
270Mb/s Serializer
for SDI and DVB-ASI
GS9092 Data Sheet
Description
The GS9092 is a 270Mb/s serializer with an internal
FIFO and an integrated cable driver. It contains all the
necessary blocks to realize a transmit solution for
SD-SDI and DVB-ASI applications.
In addition to serializing the input data stream, the
GS9092 performs NRZI-to-NRZ encoding and
scrambling as per SMPTE 259M-C when operating in
SMPTE mode. When operating in DVB-ASI mode, the
device will insert K28.5 sync characters and 8b/10b
encode the data prior to serialization.
Parallel data inputs are provided for 10-bit multiplexed
formats at SD signal rates. A 27MHz parallel clock input
signal is also required.
The integrated cable driver features an adjustable
signal swing and common mode operating point offering
fully compliant SMPTE 259M-C cable driver
connectivity.
The GS9092 includes a range of data processing
functions such as automatic standards detection and
EDH support. The device can also insert TRS signals,
re-map illegal code words, and generate and insert
SMPTE 352M payload identifier packets. All processing
features are optional and may be enabled/disabled via
external control pin(s) and/or host interface
programming.
The GS9092 also incorporates a video line-based FIFO.
This FIFO may be used in four user-selectable modes
to carry out tasks such as data delay, clock phase
interchange, MPEG packet insertion and clock rate
interchange, and ancillary data packet insertion.
The device may also be used as a low-latency
parallel-to-serial converter where the SMPTE
scrambling block will be the only processing feature
enabled.
The GS9092 is Pb-free, and the encapsulation
compound does not contain halogenated flame
retardant (RoHS compliant).
28202 - 2 September 2005
1 of 58
www.gennum.com

1 page




GS9092 pdf
www.DataSheet4U.com
1. Pin Out
1.1 Pin Assignment
GS9092 Data Sheet
LF-
1 56 55 54 53 52 51 50 49 48 47 46 45
44 43 42
IO_GND
PLL_GND
2
41 DIN9 (INSYNCIN)
PLL_VDD
3
40 DIN8 (KIN)
CD_VDD
4
SDO
SDO
5
6
CD_GND
NC
RSET
7
8
9
VBG
10
SDO_EN
11
GS9092
XXXXE3
YYWW
GENNUM
39 DIN7
38 DIN6
37 DIN5
36 DIN4
35 DIN3
34 DIN2
33 DIN1
32 DIN0
IOPROC_EN 12
31 WR_RESET
JTAG/HOST
13
30 WR_CLK
RESET
14
15
16
17 18
29
19 20 21 22 23 24 25 26 27 28
IO_VDD
Center Pad
(bottom of package)
28202 - 2 September 2005
5 of 58

5 Page





GS9092 arduino
www.DataSheet4U.com
Table 1-1: Pin Descriptions (Continued)
Pin
Number
55
Name
VCO_GND
Timing
Analog
56 LF+
Analog
– Center Pad
GS9092 Data Sheet
Type Description
Input
Power
Input
Power
Ground connection for Voltage-Controlled-Oscillator. Connect to GND.
Loop filter component connection. Connect to LF- through a capacitor.
See Typical Application Circuit on page 55.
Connect to GND following recommendations in Recommended PCB
Footprint on page 57.
2. Electrical Characteristics
2.1 Absolute Maximum Ratings
Parameter
Supply Voltage Core
Supply Voltage I/O
Input Voltage Range (any input)
Ambient Operating Temperature
Storage Temperature
ESD protection on all pins (see note 1)
NOTES:
1. HBM, per JESDA - 114B
Value/Units
-0.3V to +2.1V
-0.3V to +3.47V
-2.0V to +5.25V
-20°C < TA < 85°C
-40°C < TSTG < 125°C
1kV
28202 - 2 September 2005
11 of 58

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet GS9092.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
GS9090GenLINX-R III 270Mb/s DeserializerGennum Corporation
Gennum Corporation
GS9090AGenLINX-R III 270Mb/s DeserializerGennum Corporation
Gennum Corporation
GS9090BGenLINX III 270Mb/s DeserializerGennum Corporation
Gennum Corporation
GS9091B270Mb/s DeserializerSemtech
Semtech

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar