DataSheet.es    


PDF ET12864BV1 Data sheet ( Hoja de datos )

Número de pieza ET12864BV1
Descripción LCD Module
Fabricantes East ET 
Logotipo East ET Logotipo



Hay una vista previa y un enlace de descarga de ET12864BV1 (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! ET12864BV1 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
LCD MODULE
ET12864BV1
Sep.26, 2005
PRODUCT SPECIFICATION
FOR LCM MODULE
MODULE NO. : ET12864BV1
REVERSION : V1
TYPE
: COB
Customer Approval:
PREPARED BY
CHECKED BY
APPROVED BY
DATE
DATE
DATE
EAST ET TECHNOLOGY CO., LTD.
Tel: 86-755-83427955 61332400
E-mail: east@eastet .com
Fax: 86-755-83421997
Http//www.eastet.com
1

1 page




ET12864BV1 pdf
www.DataSheet4U.com
LCD MODULE
ET12864BV1
Sep.26, 2005
3. ABSOLUTE MAXIMUM RATINGS ( Ta = 25°C )
Table 1. Absolute Maximum Ratings
Parameter
Supply voltage for logic
Supply current
Supply voltage for
LED(Red/Green/Blue)
Supply current for LED
Operating temperature
Storage temperature
*Note: Based on Vss=0V.
Symbol
Vdd
Idd
Vled
Iled
Top
Tst
Min
-0.3
-
-20
-30
Type
5.0
4.8
Max
6.0
10
5.0
120
70
80
Unit
V
mA
V
mA
°C
°C
4. OPERATING PRINCIPLES & METHODS
Table 2. Interface Pin Connections
1 VSS 0V
Ground
2
VDD
5.0V
Supply voltage for logic Ground
3 VO
Input voltage for LCD
4 RS H/L
H: DB<0:7> Display RAM Data, L: DB<0:7> Instruction Data
5 R/W H/L
H: Read mode, L: Write mode
6E
H, HL
Chip enable signal
7 DB0 H/L
Data bit 0
8 DB1 H/L
Data bit 1
9 DB2 H/L
Data bit 2
10 DB3 H/L
Data bit 3
11 DB4 H/L
Data bit 4
12 DB5 H/L
Data bit 5
13 DB6 H/L
Data bit 6
14 DB7 H/L
Data bit 7
15 CS1 H/L
Chip select signal for IC
16 CS2 H/L
Chip select signal for IC
EAST ET TECHNOLOGY CO., LTD.
Tel: 86-755-83427955 61332400
E-mail: east@eastet .com
Fax: 86-755-83421997
Http//www.eastet.com
5

5 Page





ET12864BV1 arduino
www.DataSheet4U.com
LCD MODULE
ET12864BV1
Sep.26, 2005
10. USING LCD MODULES
Liquid Crystal Display Modules
LCD is composed of glass and polarizer. Pay attention to the following items when handling.
(1) Please keep the temperature within specified range for use and storage. Polarization degradation,
bubble generation or polarizer peel-off may occur with high temperature and high humidity.
(2) Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass,
tweezers, etc.).
(3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors
made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and
isopropylalcohol.
(4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like
chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface.
(5) Wipe off saliva or water drops immediately, contact with water over a long period of time may cause
deformation or color fading.
(6) Avoid contacting oil and fats.
(7) Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the
polarizers. After products are tested at low temperature they must be warmed up in a container before coming
is contacting with room temperature air.
(8) Do not put or attach anything on the display area to avoid leaving marks on.
(9) Do not touch the display with bare hands. This will stain the display area and degradate insulation
between terminals (some cosmetics are determinated to the polarizers).
(10) As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid
dropping or jarring.
Installing LCD Modules
The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following
items when installing the LCM.
(1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
(2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting
plate should have enough height to avoid causing stress to the module surface, refer to the individual
specifications for measurements. The measurement tolerance should be ±0.1mm.
Precaution for Handing LCD Modules
Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive
shocks to the module or making any alterations or modifications to it.
(1) Do not alter, modify or change the shape of the tab on the metal frame.
(2) Do not make extra holes on the printed circuit board, modify its shape or change the positions of
components to be attached.
(3) Do not damage or modify the pattern writing on the printed circuit board.
(4) Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
(5) Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
(6) Do not drop, bend or twist LCM.
EAST ET TECHNOLOGY CO., LTD.
Tel: 86-755-83427955 61332400
E-mail: east@eastet .com
Fax: 86-755-83421997
Http//www.eastet.com
11

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet ET12864BV1.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ET12864BV1LCD ModuleEast ET
East ET

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar