|
|
PDF CM057 Data sheet ( Hoja de datos )
| Número de pieza | CM057 | |
| Descripción | (CM053 - CM058) Option Card | |
| Fabricantes | Yaskawa | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CM057 (archivo pdf) en la parte inferior de esta página. Total 4 Páginas | ||
|
No Preview Available !
DeviceNetTM Option Card
CM053, CM056, CM057, CM058
! This document applies to the Yaskawa GPD515/G5, F7, G7 and P7 drives.
! Unpack the DeviceNet Option (CM05x) and verify that all components are present and undamaged. Check the EPROM label
to verify that the DeviceNet Option (CM05x) card is the correct card for the drive.
wwwD.rdivaetasheetK4iut.Ncoummber
G5 CM053
Option Board Number
46S03318-001x
EPROM Label Designation
VST80007x
Qty.
1
F7 CM056
46S03318-002x
VST80003x
1
G7 CM057
46S03318-003x
VST80004x
1
P7 CM058
46S03318-004x
VST80005x
1
DeviceNet Option (CM05x) Installation Guide (IG.AFD.14)
1
! Connect power to the drive and verify that the drive functions correctly. This includes running the drive from the operator keypad. Refer to the appropriate drive technical
manual for information on connecting and operating the drive.
! Remove power from the drive and wait for the charge lamp to be completely extinguished. Wait at least five additional minutes for the drive to be completely discharged.
Measure the DC BUS voltage and verify that it is at a safe level.
! Remove the operator keypad and drive cover.
# Remove the operator keypad and loosen any screws on the front of the terminal
cover. Simultaneously pushing the locking tabs on the bottom right and left sides of
the terminal cover inward, pull the bottom edge of the terminal cover outward.
# Loosen any screws on the front of the control cover. Simultaneously pushing the
locking tabs on the bottom right and left sides of the control cover inward, pull the
bottom edge of the control cover outward. The drive control card should be visible.
# Remove the option card hold-down on the left side of the drive case by carefully
compressing the top and bottom until it becomes free of its holder. Lift it out.
! Mount the DeviceNet Option (CM05x) on the drive.
# Align the J1 connector on the back of the DeviceNet Option (CM05x) with its
mating 2CN connector on the drive control card.
# Align the three standoffs on the front of the drive control board with the three holes
on the right side of the DeviceNet Option (CM05x).
# Press the DeviceNet Option (CM05x) firmly onto the drive 2CN connector and
standoffs until the J1 connector is fully seated on 2CN and the drive standoffs have
locked into their appropriate holes.
# Replace the option card hold down.
# Connect the ground wire from the ground terminal E on the option card to a ground
terminal on the terminal assembly.
! Apply power to the drive and verify that the drive functions correctly.
! Connect to the DeviceNet network as shown in the figure to the right.
Terminal Name Wire Color
Description
1
V- Black
Communication GND
2 CAN_L Blue
CAN Data Low
3 Shield Bare
Cable Shield
4 CAN_H White
CAN Data High
5 V+ Red
Communications +24Vdc
Mounting the DeviceNet Option on an F7 drive
Yaskawa Electric America, Inc – www.drives.com
IG.AFD.14, Page 1 of 4
Date: 07/01/04, Rev: 04-07
1 page | ||
| Páginas | Total 4 Páginas | |
| PDF Descargar | [ Datasheet CM057.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CM053 | (CM053 - CM058) Option Card | Yaskawa |
| CM056 | (CM053 - CM058) Option Card | Yaskawa |
| CM057 | (CM053 - CM058) Option Card | Yaskawa |
| CM058 | (CM053 - CM058) Option Card | Yaskawa |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |