DataSheet.es    


PDF LM150K Data sheet ( Hoja de datos )

Número de pieza LM150K
Descripción 3-Amp Adjustable Regulators
Fabricantes National Semiconductor 
Logotipo National Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de LM150K (archivo pdf) en la parte inferior de esta página.


Total 14 Páginas

No Preview Available ! LM150K Hoja de datos, Descripción, Manual

May 1998
LM150/LM350A/LM350
3-Amp Adjustable Regulators
General Description
The LM150 series of adjustable 3-terminal positive voltage
regulators is capable of supplying in excess of 3A over a
1.2V to 33V output range. They are exceptionally easy to
use and require only 2 external resistors to set the output
voltage. Further, both line and load regulation are compa-
rable to discrete designs. Also, the LM150 is packaged in
standard transistor packages which are easily mounted and
handled.
In addition to higher performance than fixed regulators, the
LM150 series offers full overload protection available only in
IC’s. Included on the chip are current limit, thermal overload
protection and safe area protection. All overload protection
circuitry remains fully functional even if the adjustment termi-
nal is accidentally disconnected.
Normally, no capacitors are needed unless the device is situ-
ated more than 6 inches from the input filter capacitors in
which case an input bypass is needed. An output capacitor
can be added to improve transient response, while bypass-
ing the adjustment pin will increase the regulator’s ripple re-
jection.
Besides replacing fixed regulators or discrete designs, the
LM150 is useful in a wide variety of other applications. Since
the regulator is “floating” and sees only the input-to-output
differential voltage, supplies of several hundred volts can be
regulated as long as the maximum input to output differential
is not exceeded, i.e., avoid short-circuiting the output.
By connecting a fixed resistor between the adjustment pin
and output, the LM150 can be used as a precision current
regulator. Supplies with electronic shutdown can be
achieved by clamping the adjustment terminal to ground
which programs the output to 1.2V where most loads draw
little current.
The part numbers in the LM150 series which have a K suffix
are packaged in a standard Steel TO-3 package, while those
with a T suffix are packaged in a TO-220 plastic package.
The LM150 is rated for −55˚C TJ +150˚C, while the
LM350A is rated for −40˚C TJ +125˚C, and the LM350 is
rated for 0˚C TJ +125˚C.
Features
n Adjustable output down to 1.2V
n Guaranteed 3A output current
n Guaranteed thermal regulation
n Output is short circuit protected
n Current limit constant with temperature
n P+ Product Enhancement tested
n 86 dB ripple rejection
n Guaranteed 1% output voltage tolerance (LM350A)
n Guaranteed max. 0.01%/V line regulation (LM350A)
n Guaranteed max. 0.3% load regulation (LM350A)
Applications
n Adjustable power supplies
n Constant current regulators
n Battery chargers
Connection Diagrams
(TO-3 STEEL)
Metal Can Package
(TO-220)
Plastic Package
DS009061-4
Case is Output
Bottom View
Order Number LM150K STEEL
or LM350K STEEL
See NS Package Number K02A
Order Number LM150K/883
See NS Package Number K02C
© 1999 National Semiconductor Corporation DS009061
DS009061-5
Front View
Order Number LM350AT or LM350T
See NS Package Number T03B
www.national.com

1 page




LM150K pdf
Application Hints
In operation, the LM150 develops a nominal 1.25V reference
voltage, VREF, between the output and adjustment terminal.
The reference voltage is impressed across program resistor
R1 and, since the voltage is constant, a constant current I1
then flows through the output set resistor R2, giving an out-
put voltage of
tween 500 pF and 5000 pF. A 1 µF solid tantalum (or 25 µF
aluminum electrolytic) on the output swamps this effect and
insures stability.
LOAD REGULATION
The LM150 is capable of providing extremely good load
regulation but a few precautions are needed to obtain maxi-
mum performance. The current set resistor connected be-
tween the adjustment terminal and the output terminal (usu-
ally 240) should be tied directly to the output (case) of the
regulator rather than near the load. This eliminates line
drops from appearing effectively in series with the reference
and degrading regulation. For example, a 15V regulator with
0.05resistance between the regulator and load will have a
load regulation due to line resistance of 0.05x IOUT. If the
set resistor is connected near the load the effective line re-
sistance will be 0.05(1 + R2/R1) or in this case, 11.5 times
worse.
Figure 2 shows the effect of resistance between the regula-
tor and 240set resistor.
FIGURE 1.
DS009061-7
Since the 50 µA current from the adjustment terminal repre-
sents an error term, the LM150 was designed to minimize
IADJ and make it very constant with line and load changes.
To do this, all quiescent operating current is returned to the
output establishing a minimum load current requirement. If
there is insufficient load on the output, the output will rise.
EXTERNAL CAPACITORS
An input bypass capacitor is recommended. A 0.1 µF disc or
1 µF solid tantalum on the input is suitable input bypassing
for almost all applications. The device is more sensitive to
the absence of input bypassing when adjustment or output
capacitors are used but the above values will eliminate the
possibility of problems.
The adjustment terminal can be bypassed to ground on the
LM150 to improve ripple rejection. This bypass capacitor
prevents ripple from being amplified as the output voltage is
increased. With a 10 µF bypass capacitor 86 dB ripple rejec-
tion is obtainable at any output level. Increases over 10 µF
do not appreciably improve the ripple rejection at frequen-
cies above 120 Hz. If the bypass capacitor is used, it is
sometimes necessary to include protection diodes to prevent
the capacitor from discharging through internal low current
paths and damaging the device.
In general, the best type of capacitors to use is solid tanta-
lum. Solid tantalum capacitors have low impedance even at
high frequencies. Depending upon capacitor construction, it
takes about 25 µF in aluminum electrolytic to equal 1 µF
solid tantalum at high frequencies. Ceramic capacitors are
also good at high frequencies, but some types have a large
decrease in capacitance at frequencies around 0.5 MHz. For
this reason, 0.01 µF disc may seem to work better than a 0.1
µF disc as a bypass.
Although the LM150 is stable with no output capacitors, like
any feedback circuit, certain values of external capacitance
can cause excessive ringing. This occurs with values be-
DS009061-8
FIGURE 2. Regulator with Line Resistance
in Output Lead
With the TO-3 package, it is easy to minimize the resistance
from the case to the set resistor, by using two separate leads
to the case. The ground of R2 can be returned near the
ground of the load to provide remote ground sensing and im-
prove load regulation.
PROTECTION DIODES
When external capacitors are used with any IC regulator it is
sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator. Most 10 µF capacitors have low enough
internal series resistance to deliver 20A spikes when
shorted. Although the surge is short, there is enough energy
to damage parts of the IC.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the regu-
lator, and the rate of decrease of VIN. In the LM150, this dis-
charge path is through a large junction that is able to sustain
25A surge with no problem. This is not true of other types of
positive regulators. For output capacitors of 25 µF or less,
there is no need to use diodes.
The bypass capacitor on the adjustment terminal can dis-
charge through a low current junction. Discharge occurs
when either the input or output is shorted. Internal to the
LM150 is a 50resistor which limits the peak discharge cur-
rent. No protection is needed for output voltages of 25V or
5 www.national.com

5 Page





LM150K arduino
Typical Applications (Continued)
Tracking Preregulator
DS009061-27
Adjusting Multiple On-Card Regulators
with Single Control*
Minimum load — 10 mA
*All outputs within ±100 mV
AC Voltage Regulator
DS009061-28
Simple 12V Battery Charger
DS009061-30
DS009061-29
DS009061-48
Use of RS allows low charging rates with fully charged battery.
**1000 µF is recommended to filter out any input transients
11 www.national.com

11 Page







PáginasTotal 14 Páginas
PDF Descargar[ Datasheet LM150K.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LM1503-Amp Adjustable RegulatorsNational Semiconductor
National Semiconductor
LM150ADJUSTABLE VOLTAGE REGULATORS THREE-TERMINAL 3 ASTMicroelectronics
STMicroelectronics
LM1503 AMP POSITIVE ADJUSTABLE VOLTAGE REGULATORSeme LAB
Seme LAB
LM150LM150/LM350A/LM350 3-Amp Adjustable Regulators (Rev. B)Texas Instruments
Texas Instruments

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar