|
|
PDF G5Y-1 Data sheet ( Hoja de datos )
| Número de pieza | G5Y-1 | |
| Descripción | Low Signal Relay | |
| Fabricantes | Omron Electronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de G5Y-1 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
www.datasheet4u.com
Low Signal Relay
s Miniature 9.0 H x 11.5 W x 20.5 L mm
(0.35 H x 0.45 W x 0.81 L in)
s Shield plate and resin-molded relay
base provide excellent high-frequency
characteristics: isolation of 68 dB (typ.),
insertion loss of 0.20 dB (typ.), and
VSWR of 1.30 (typ.) at 900 MHz
s Ultrasmall and lightweight with pickup
coil power of 170 mW (112 mW for
high-sensitivity type)
s Plastic sealed construction highly
resistant to adverse environmental
conditions
s High shock resistance
G5Y-1
Ordering Information
To Order: Select the part number and add the desired coil voltage rating (e.g., G5Y-1-DC12).
Type
Standard
High-sensitivity
Contact form
SPDT
Construction
Fully-sealed
Part number
G5Y-1
G5Y-1-H
Specifications
s CONTACT DATA
Load
Rated load
Contact material
Carry current
Max. operating voltage
Max. operating current
Max. switching capacity
Min. permissible load
* Denotes the value at VSWR ≤1.2.
Resistive load (p.f. = 1)
24 VAC 0.01 A
24 VDC 0.01 A
1 W at 900 MHz*
Au clad Cu alloy
0.10 A
30 VAC, 30 VDC
0.10 A
1 VA, 1W
10 mA at 10 mVDC
1 page  
G5Y-1
www.datasheet4u.com
Dimensions
Unit: mm (inch)
s RELAY
Terminal arrangement/
Internal connections
(bottom view)
G5Y-1
Mounting holes
(bottom view)
Note: Parts marked with111222333444555 and
indicate mounting direction mark on G5Y relay.
Hints on Correct Use
How to design PC Board
s PC BOARD SELECTION
Thickness of PC board
PC boards are generally available in the following
thicknesses: 0.8 (0.03), 1.0 (0.04), 1.2 (0.05), 1.6 (0.06), and
2.0 mm (0.08 in). In determining the thickness of the PC
board to be used, the pattern widths of the microstrips must
be taken into account. First, determine the applicable pattern
widths based on the intended arrangement of components on
the PC board. Then select the appropriate PC board
thickness.
PC board material
The base materials of PC boards can be divided into two
types: epoxy type and phenolic type. For high-frequency
circuits, glass epoxy type double-sided PC boards are
recommended because of their distinct dielectric constant
and material stability. However, paper epoxy type or paper
phenolic type single-sided PC boards may also be used if
cost factor is essential. Refer to “Examples of packaging
design” for mounting the relay on a single-sided PC board.
s PATTERN DESIGN
Preparation for pattern design
Relay mounting direction
The mounting direction of each relay must be taken into
account for the relay to function with maximum performance.
Shock resistance is one of the representative relay
performance characteristics greatly influenced by the relay
mounting direction. Refer to the Shock Resistance
Characteristic in “Characteristic Data” section.
Note that the shock resistance of a relay (NC contact), with its
coil in the nonenergized state, is governed greatly by the
mounting direction of the relay.
Terminal hole diameters, land diameters, and land shapes
(DC circuit)
Terminal hole diameter and land diameter
Select the appropriate terminal hole diameter and land
diameter from the following table based on the PC board
mounting hole drawing. Land diameters may be reduced to
less than those listed below if thru-hole connection process is
to be employed.
Terminal hole diameters and land diameters
Unit: mm (inch)
Terminal hole
diameter
Nominal value
0.6 (0.02)
0.8 (0.03)
1.0 (0.04)
1.2 (0.05)
1.3 (0.05)
1.5 (0.06)
1.6 (0.06)
2.0 (0.08)
Minimum
land
diameter
1.5 (0.06)
1.8 (0.07)
2.0 (0.08)
2.5 (0.10)
3.0 (0.12)
Tolerance
± 0.1 (± 0.004)
5
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet G5Y-1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| G5Y-1 | Low Signal Relay | Omron Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |