DataSheet.es    


PDF LM1291 Data sheet ( Hoja de datos )

Número de pieza LM1291
Descripción Video PLL System for Continuous-Sync Monitors
Fabricantes National Semiconductor 
Logotipo National Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de LM1291 (archivo pdf) en la parte inferior de esta página.


Total 12 Páginas

No Preview Available ! LM1291 Hoja de datos, Descripción, Manual

June 1995
LM1291
Video PLL System for Continuous-Sync Monitors
General Description
The LM1291 is an integrated horizontal time base solution
specifically designed to operate in continuous-sync video
monitors It automatically synchronizes to any H frequency
from 22 kHz to 125 kHz and provides the drive pulse to the
high power deflection circuit
Available sync processing includes a vertical sync separator
and a composite video sync stripper An internal sync selec-
tion scheme gives highest priority to separate H and V sync
then composite sync and finally sync on video no external
switching between sync sources is necessary The LM1291
provides polarity-normalized H HV and V sync outputs
along with logic flags which show the respective input polar-
ities
The design uses an on-chip FVC (Frequency-to-Voltage
Converter) to set the center frequency of the VCO (Voltage-
Controlled Oscillator) This technique allows autosync oper-
ation over the entire frequency range using just one opti-
mized set of external components
The system includes a second phase detector which com-
pensates for storage time variation in the horizontal output
transistor the picture’s horizontal position is thus indepen-
dent of temperature and component variance
The LM1291 provides DC control pins for H Drive duty cycle
and flyback phase
Features
Y Wide continuous autosync range 22 kHz to 125 kHz
(1 5 7) with no component switching or external adjust-
ments
Y No manufacturing trims required internal VCO capaci-
tor trimmed on chip
Y No costly high-precision components needed
Y Low phase jitter (1 3 ns at 100 kHz)
Y DC controlled H phase and duty cycle
Y Video mute pulse for blanking during H frequency
transitions
Y Input sync prioritization
Y Clamp pulse position and width control
Y Continuous clamp pulse output even with no sync input
Y Resistor-programmable minimum and maximum VCO
frequency
Y X-ray input disables H drive and mutes video until VCC
powered down
Y H drive disabled for VCC k 9 5V
Y Horizontal output transistor protected against accidental
turn-on during flyback
Y Capacitor-programmable frequency ramping dfVCO dt
protects H output transistor during scanning mode
changes
Connection Diagram
FIGURE 1
Order Number LM1291N
See NS Package Number N28B
C1995 National Semiconductor Corporation TL H 12323
TL H 12323 – 1
RRD-B30M115 Printed in U S A

1 page




LM1291 pdf
Block Diagram
FIGURE 3
TL H 12323 – 3
Pin Descriptions
See Figures 4 through 15 for input and output schematics
Pin 1 - CLAMP CNTL This low-impedance current-mode
input pin is internally biased to 2V The direction of current
sets the pulse position (back porch or sync-tip) while the
current magnitude sets the pulse width In a typical applica-
tion a control voltage of 0V–4V is applied to this pin
through a 15 kX resistor A voltage below 2V positions the
pulse on the back porch of the horizontal sync pulse and
decreasing voltage narrows the pulse A voltage above 2V
sets the pulse on the H sync-tip (slightly delayed from the
leading edge) and increasing voltage narrows the pulse At
the boundary of the switchover between the two modes
there is a narrow region of uncertainty resulting in oscilla-
tion which should be no problem in most applications
When there is no H sync in sync-tip mode the clamp pulse
is generated by the VCO at the frequency preset by pin 5
(fMIN) This feature is intended for use in On Screen Display
systems
Pin 2 - CLAMP PULSE Active-low clamp pulse output See
Figure 4 for the output schematic
Pin 3 - VIDEO MUTE This NPN open-collector output pro-
duces an active-low pulse when triggered by a step change
of H sync frequency See Figure 5 for the output schematic
Pin 4 - fMAX A resistor from this pin to ground sets the
upper frequency limit of the VCO fMAX is approximately
1 8 c 109
Hz
(RMAX a 500)
Pin 5 - fMIN A resistor from this pin to ground sets the lower
frequency limit of the VCO fMIN is approximately
7 5 c 103 a 5 6 c 108 Hz
(RMIN a 500)
Pin 6 - VREF CAP This is the decoupling pin for the internal
8 2V reference It should be decoupled to pin 21 (GND) via
a short path with a cap of at least 470 mF
Pin 7 - VCC 12V nominal power supply pin This pin should
be decoupled to pin 21 (GND) via a short path with a cap of
at least 47 mF
Pin 8 - V SYNC IN This pin accepts AC-coupled V sync of
either polarity The pin is internally biased at 5 2V its input
resistance is approximately 50 kX For best noise immunity
a resistor of 2 kX or less should be connected from the
input side of the coupling cap to ground See Figure 6 for
the input schematic
Pin 9 - COMP VIDEO IN The composite video sync stripper
is active only when no signal is present at pin 12 (H HV IN)
The signal to pin 9 must have negative-going sync tips
which are at least 0 14V below black level For best noise
immunity a resistor of 2 kX or less should be connected
from the input side of the coupling cap to ground See Fig-
ure 7 for the input schematic
Pin 10 - H HV CAP A capacitor is connected from this pin
to ground for detecting the polarity and existence of H HV
sync at pin 12
5

5 Page





LM1291 arduino
11

11 Page







PáginasTotal 12 Páginas
PDF Descargar[ Datasheet LM1291.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
LM129Precision ReferenceNational Semiconductor
National Semiconductor
LM1296.9V Precision Voltage ReferenceLinear Technology
Linear Technology
LM1290Autosync Horizontal Deflection ProcessorNational Semiconductor
National Semiconductor
LM1290NAutosync Horizontal Deflection ProcessorNational Semiconductor
National Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar