DataSheet.es    


PDF ICX059AK Data sheet ( Hoja de datos )

Número de pieza ICX059AK
Descripción 1/3-inch CCD Image Sensor
Fabricantes Sony Corporation 
Logotipo Sony Corporation Logotipo



Hay una vista previa y un enlace de descarga de ICX059AK (archivo pdf) en la parte inferior de esta página.


Total 18 Páginas

No Preview Available ! ICX059AK Hoja de datos, Descripción, Manual

ICX059AK
ww1w./D3ata-Sihneect4hU.coCmCD Image Sensor for PAL Color Camera
For the availability of this product, please contact the sales office.
Description
The ICX059AK is an interline CCD solid-state image
sensor suitable for PAL color video cameras. High
16 pin DIP (Plastic)
resolution is achieved through the use of Ye, Cy, Mg,
and G complementary color mosaic filters. At the
same time, high sensitivity and low dark current are
achieved through the adoption of HAD (Hole-
Accumulation Diode) sensors.
This chip features a field period readout system and
an electronic shutter with variable charge-storage time.
Features
High resolution, high sensitivity and low dark current
Continuous variable-speed shutter
1/50s (Typ.), 1/120s to 1/10000s
Low smear
Excellent antiblooming characteristics
Ye, Cy, Mg, and G complementary color mosaic filters on chip
Horizontal register:
5V drive
Reset gate:
5V drive
V
3
Pin 9
Pin 1
2
12
H 40
Device Structure
Optical size:
Number of effective pixels:
Number of total pixels:
Interline CCD image sensor
Chip size:
Unit cell size:
Optical black:
Number of dummy bits:
Substrate material:
1/3-inch format
752 (H) × 582 (V) approx. 440K pixels
795 (H) × 596 (V) approx. 470K pixels
Optical black position
(Top View)
6.00mm (H) × 4.96mm (V)
6.50µm (H) × 6.25µm (V)
Horizontal (H) direction: Front 3 pixels, rear 40 pixels
Vertical (V) direction: Front 12 pixels, rear 2 pixels
Horizontal 22
Vertical 1 (even field only)
Silicon
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E91Y29B5Y-PS

1 page




ICX059AK pdf
ICX059AK
Cwlwowc.kDaEtaqSuhieveat4leUn.ctomCircuit Constant
Item
Capacitance between vertical transfer
clock and GND
Capacitance between vertical transfer
clocks
Capacitance between horizontal
transfer clock and GND
Capacitance between horizontal
transfer clocks
Capacitance between horizontal final
stage transfer clock and GND
Capacitance between reset gate clock
and GND
Capacitance between substrate clock
and GND
Vertical transfer clock series resistor
Vertical transfer clock ground resistor
Horizontal transfer clock series resistor
Symbol
CφV1, CφV3
CφV2, CφV4
CφV12, CφV34
CφV23, CφV41
CφV13
CφV24
CφH1, CφH2
CφHH
CφLH
CφRG
CφSUB
R1, R2, R3, R4
RGND
RφH
Min. Typ. Max. Unit Remarks
1000
pF
560 pF
470 pF
390 pF
180 pF
100 pF
47 pF
51 pF
8 pF
8 pF
270 pF
80
15
15
Vφ1
R1
CφV12
Vφ2
R2
CφV41
CφV1
CφV2
CφV24
R4
CφV4 RGND CφV3
CφV34
CφV23
CφV13
R3
Vφ4 Vφ3
Vertical transfer clock equivalent circuit
RφH
Hφ1
CφH1
CφHH
RφH
Hφ2
CφH2
Horizontal transfer clock equivalent circuit
–5–

5 Page





ICX059AK arduino
ICX059AK
wwDwe.DfaintaiStihoenet4oUf.csotmandard imaging conditions
1) Standard imaging condition I:
Use a pattern box (luminance 706cd/m2, color temperature of 3200K halogen source) as a subject. (Pattern
for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter and
image at F5.6. The luminous intensity to the sensor receiving surface at this point is defined as the standard
sensitivity testing luminous intensity.
2) Standard imaging condition II:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition I. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the Y signal (Ys) at the center of the screen and substitute the value into the following
formula.
S = Ys ×
250
50
[mV]
2. Saturation signal
Set to standard imaging condition II. After adjusting the luminous intensity to 10 times the intensity with
average value of the Y signal output, 200mV, measure the minimum value of the Y signal.
3. Smear
Set to standard imaging condition II. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the Y signal output, 200mV. When the readout clock is
stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure
the maximum value YSm [mV] of the Y signal output and substitute the value into the following formula.
Sm =
YSm
200
×
1
500
×
1
10
× 100 [%] (1/10V method conversion value)
4. Video signal shading
Set to standard imaging condition II. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity so
that the average value of the Y signal output is 200mV. Then measure the maximum (Ymax [mV]) and
minimum (Ymin [mV]) values of the Y signal and substitute the values into the following formula.
SHy = (Ymax – Ymin)/200 × 100 [%]
5. Uniformity between video signal channels
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the maximum (Crmax, Cbmax [mV]) and minimum (Crmin, Cbmin
[mV]) values of the R – Y and B – Y channels of the chroma signal and substitute the values into the
following formula.
Sr = | (Crmax – Crmin)/200 | × 100 [%]
Sb = | (Cbmax – Cbmin)/200 | × 100 [%]
6. Dark signal
Measure the average value of the Y signal output (Ydt [mV]) with the device ambient temperature 60°C and
the device in the light-obstructed state, using the horizontal idle transfer level as a reference.
– 11 –

11 Page







PáginasTotal 18 Páginas
PDF Descargar[ Datasheet ICX059AK.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ICX059AK1/3-inch CCD Image SensorSony Corporation
Sony Corporation
ICX059AKBDiagonal 6mm (Type 1/3) CCD Image SensorSony Corporation
Sony Corporation
ICX059ALBDiagonal 6mm (Type 1/3) CCD Image SensorSony Corporation
Sony Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar